Elements Renegade DRN1006DS

To Next Page

PART LIST FOR CHAIR

LISTE DES PIÈCES POUR CHAISE

No.

CODE.

Q'TY

PDRN100SCBFR

PDRN100SCSEA

PDRN100SCLEG

Assembly Instruction for/ Instructions D'assemblage pour

CROSS BACKSIDE CHAIR/ CHAISE ARRIÈRE

DRN1006DS & DRN3006DS

Side chair back frame

Cadre arrière de chaise latérale.

Side chair seat frame

Cadre de siège de chaise latérale

Side chair front leg

Patte avant de la chaise latérale

No.

CODE.

Q'TY

PDRN100SCHW

Allen bolt/ Boulon allen (Ø1/4"*2-3/8")

Allen bolt/ Boulon allen (Ø1/4"*3")

Allen key/ Clé d'allen (Ø1/8")

Spring washer/ Rondelle elastique (Ø5/16")

Flat washer/ Rondelle plates (Ø5/16")

HARDWARE LIST PACKED INSIDE BOX

LISTE DE MATÉRIEL BOÎTE INTÉRIEURE EMBALLÉE

HARDWARE DESC/ LISTE DE QUINCAILLERIE

PART DESC/ LISTE DES PIECES

Allen bolt/ Boulon allen (Ø5/16"*1-5/8")

Step:1

Étape:1

Step:2

Étape:2

Completed

Achevée

MADE IN VIETNAM/ FABRIQUÉ AU VIETNAM

PAGE 1 OF 3

Caution: Please read instructions thoroughly before unpacking assembly parts. Sharp, exposed staple tips can cause injury,

therefore, for your protection, please remove any exposed staples used in packing.

1. We recommend that you should assemble this product with the assistance of another person; this will make

assembly easier, and will help to eliminate damage to the product or injury to persons during assembly.

2. Be sure to check all packing materials carefully for small parts that may have come loose inside the carton during shipment.

3. Please do not over tighten screws or bolts.

4. Please put all parts on a non-abrasive floor before assembly, and follow the assembly steps to assemble your newly

purchased product correctly and efficiently.

Attention: S'il vous plait lire attentivement les instructions avant de déballer les pièces d'assemblage. Pour votre protection et éviter

les blessures, s'il vous plait retirer les agrafes exposés utilisés pour l'emballage.

1. Nous vous recommandons d'assembler ce produit avec l'aide d'une autre personne; cela

facilitera le montage, et aidera à éliminer les dommages au produit ou des blessures lors de l'assemblage.

2. Assurez-vous de vérifier soigneusement tous les matériaux d'emballage pour les petites pièces qui peuvent avoir été lâche à

l'intérieur du carton pendant le transport.

3. Nous vous demandons de ne pas trop serrer les vis ou des boulons.

4. ll est recommande' de mettre toutes les pièces d'assemblage sur un sol non abrasif avant l'assemblage et de suivre les étapes

d'assemblage une par pour assembler votre nouveau produit correctement et efficacement.

Only tighten all bolts when all bolts aligned with bolt inserts.

Ne serrez tous les boulons que lorsque tous les boulons sont alignés avec les inserts de boulon.

Need help?

Do you have a question about the Elements Renegade DRN1006DS and is the answer not in the manual?

This document provides assembly instructions for various furniture pieces, including a cross backside chair, a dining table, and a bench, all falling under the DRN1006DS and DRN3006DS series. The instructions are presented in both English and French, emphasizing safety and efficiency during the assembly process.

Function Description

The primary function of this manual is to guide users through the step-by-step assembly of furniture items. It details the components required for each piece (chair, dining table, bench) and provides clear visual aids to ensure correct construction. The instructions aim to enable users to assemble their newly purchased products correctly and efficiently, minimizing the risk of damage to the product or injury to persons.

Important Technical Specifications

The manual lists specific parts and hardware for each furniture item, identified by unique codes and quantities.

For the Cross Backside Chair (DRN1006DS & DRN3006DS):

Part List:
- Side chair back frame (PDRN100SCBFR): 1 unit
- Side chair seat frame (PDRN100SCSEA): 1 unit
- Side chair front leg (PDRN100SCLEG): 2 units
Hardware List (PDRN100SCHW):
- Allen bolt (Ø1/4"*3"): 4 units
- Allen bolt (Ø1/4"*2-3/8"): 4 units
- Allen bolt (Ø5/16"*1-5/8"): 2 units
- Spring washer (Ø5/16"): 10 units
- Flat washer (Ø5/16"): 10 units
- Allen key (Ø1/8"): 1 unit

For the Dining Table (DRN1006DS & DRN3006DS):

Part List:
- Counter Table Top: 1 unit
- Counter Table Legs (PDRN1006DTLEG): 2 units
- Counter Table Angle Stretcher (PDRN1006DTSTR1): 2 units
- Counter Table Straight Stretcher (PDRN1006DTSTR2): 1 unit
Hardware List (PDRN1006DTHW):
- Allen bolt (Ø5/16"*2-3/8"): 2 units
- Allen bolt (Ø1/4"*1-5/8"): 8 units
- Spring washer (Ø5/16"): 4 units
- Flat washer (Ø5/16"): 4 units
- Allen key (Ø1/8"): 1 unit
- Wooden Plugs: 2 units

For the Bench (DRN1006DS & DRN3006DS):

Part List:
- Counter Bench Top (PDRN1006BNSEA): 1 unit
- Counter Bench Legs (PDRN1006BNLEG): 2 units
- Counter Bench Angle Stretcher (PDRN1006BNSTR1): 2 units
- Counter Bench Straight Stretcher (PDRN1006BNSTR2): 1 unit
Hardware List (PDRN1006BNHW):
- Allen bolt (Ø1/4"*1-5/8"): 2 units
- Allen bolt (Ø1/4"*1-1/8"): 8 units
- Spring washer (Ø5/16"): 4 units
- Flat washer (Ø5/16"): 4 units
- Allen key (Ø1/8"): 1 unit
- Wooden Plugs: 2 units

All furniture items are manufactured in Vietnam.

Usage Features

The manual highlights several key usage features to ensure a smooth and safe assembly experience:

Assisted Assembly: It is strongly recommended to assemble the product with the assistance of another person. This facilitates the process, reduces the risk of product damage, and prevents personal injury.
Thorough Inspection: Before assembly, users are advised to carefully check all packing materials for small parts that might have come loose during shipment. This ensures no components are missing before starting the assembly.
Proper Placement: All parts should be placed on a non-abrasive floor during assembly. This prevents scratches or damage to the furniture components.
Step-by-Step Guidance: The instructions are presented in a clear, sequential step-by-step format with corresponding diagrams. This visual guidance helps users follow the assembly process accurately.
Alignment for Tightening: A crucial instruction is to "Only tighten all bolts when all bolts aligned with bolt inserts." This ensures that all components are correctly positioned and aligned before final tightening, preventing misalignment and potential damage.
Avoid Over-tightening: Users are explicitly warned not to over-tighten screws or bolts. Over-tightening can strip threads, damage components, or compromise the structural integrity of the furniture.
Staple Removal: Before unpacking assembly parts, users are cautioned to remove any sharp, exposed staple tips from the packaging to prevent injury.

Maintenance Features

While the manual primarily focuses on assembly, it implicitly suggests certain maintenance practices through its warnings and recommendations:

Careful Handling: The emphasis on preventing damage during assembly (e.g., using a non-abrasive floor, avoiding over-tightening) implies that careful handling is essential for the longevity of the furniture.
Structural Integrity: By ensuring all bolts are aligned and not over-tightened, the assembly process contributes to the structural integrity of the furniture, which is a key aspect of long-term maintenance. A well-assembled piece is less likely to loosen or break down over time.
Regular Checks (Implied): Although not explicitly stated as a maintenance feature, the detailed assembly instructions for bolts and washers suggest that periodic checks of these fasteners might be beneficial to ensure the furniture remains stable and secure over its lifespan. If components were to loosen over time, referring back to the assembly steps could help in re-securing them correctly.

In summary, this manual serves as a comprehensive guide for assembling specific furniture items from the DRN1006DS and DRN3006DS series, providing detailed part lists, hardware specifications, and critical usage instructions to ensure a safe, efficient, and correct assembly process.