20
N Parameter Min. Default Max Notes
01 Init.User 1 1 99999999 Lowest number of users called from the entrance panel
02 Final User 1 99999999 99999999 Highest number of users called from the entrance panel
03 Panel Number 0 0 99999999 ID number of the entrance panel for calls from switchboard. We advise you to always
use numbers above 99000000
04 Pre-code 0 0 9999 Number assigned to the number entered from the keypad
05 Sum number 0 0 99999999 (Only for ..../P versions)
If parameter 07 = 0, the value programmed for this parameter is added to the hardware
code of the pressed button to obtain the number of the internal user called.
E.g. Para. 05 = 10, button pressed = 8 -> the panel calls internal user 18.
06 Buttons in 2 rows 0 0 1 (Only for ..../P versions)
1 = The push-buttons of the entrance panel and those of the additional modules are
arranged in two parallel rows;
0 = The push-buttons of the entrance panel and those of the additional modules are
arranged in a single row
07 SW encoding 0 0 2 (Only for ..../P versions)
The HW-SW association of the direct call push-buttons can only be programmed when
the parameter is enabled:
0 = HW –SW association disabled.
1 = HW –SW association enabled. If number NNN is associated with push-button X,
when X is pressed the panel calls number NNN. If however 0 is associated with pu-
sh-button X, when X is pressed the panel does NOT send the call.
2 = HW –SW association enabled. If number NNN is associated with push-button X,
when X is pressed the panel calls number NNN. If however 0 is associated with pu-
sh-button X, when X is pressed the panel calls number X.
08 Tech.Prg Key 1 123 9999 Key for accessing the entrance panel setup menus.
09 Agenda Key 1 222 9999 Key for accessing the user agenda management menus
10 Key 0-R1-C 0 1 2 Procedure for inserting the key for the door lock release:
0 = press ‘0’ to enable the key to be entered
1 = press R and 1 to enter the key
2 = press “
” to enter the key
11 Digit number 4 8 8 Number of digits used in digibus communication.
The only possible options are 4 or 8.
12 Select Language 0 0 8 Parameter for selecting the message display language
0 = Italian
1 = English
2 = Spanish
3 = French
4 = German
5 = Portuguese
6 = Swedish
7 = Polish
8 = Slovenian
13 Panel Block 0011 = the panel is blocked and does not make calls
14 Enab. Priority 0011 = the entrance panel has priority over other panels connected in parallel. If there is a
call in progress from the other panels, it is possible to make a call by disconnecting the
line to the other panels.
15 Enab.Lock 0 1 6 Configures the door lock opening modes. See “DESCRIPTION OF FUNCTIONS AND
PARAMETERS - Lock activation mode” (page 24)
16 Enab.Camera 0110 = the video camera is not enabled, therefore the entrance panel only makes audio
calls;
1 = the video camera is enabled and the entrance panel makes audio / video calls
17 Enab.Panel Tone 0110 = acoustic signals are disabled
1 = acoustic signals are enabled
18 Enab.Self-start 0 0 255 0 = self-start disabled, otherwise self-start is enabled according as described in “DE-
SCRIPTION OF FUNCTIONS AND PARAMETERS - Enable self-start”.
19 Enab.Switchboard.
Call
0 0 3 Enables the call to switchboard function. Used when the entrance panel is a secon-
dary panel in a building complex:
0 = Switchboard call disabled
1 = Switchboard call from direct call push-button programmed in Par. 20
2 = Switchboard call from “
” button
3 = Switchboard call from direct call push-button and
from “
” button
ENTRANCE PANEL PARAMETERS
The entrance parameters are listed in the following table:
EN
To Next Page
Loading...
Need help?
General
