Emerson E300 Series - Keypad Menu and Parameter Navigation; Keypad Menu and Parameter Shortcuts

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
User Menu A Commissioning
Advanced
Parameters
Diagnostics Optimization CT MODBUS RTU Technical Data
110 E300 Design Guide
Issue Number: 1
5.6 Keypad menu and parameter navigation
The drive parameter structure consists of menus and parameters, which at power up displays the User Menu A due to the default security, parameter
access level in User Security Status (H02).
The keypad will display both the menu and the parameter list within the drive as described following. All menus are structured alphabetically A, B, C
through to Z, these also covering any additional option modules installed. All parameters within each menu are numbered from 00, 01, 02, 03, up to
the highest parameter in the menu, which will vary dependant upon the menu.
The left and right navigation keys can be used to navigate between “All Menus” and the up and down navigation keys are
used to navigate between “All Parameters” within the menu.
The security and parameter access in User Security Status (H02) should be set to 'All Menus'.
Figure 5-4 Parameter navigation
The navigation keys will only move between all menus if “All Menus” have been enabled User Security Status (H02). Refer to section 5.5 Changing
security and parameter access on page 109. The menus and parameters will roll over in both directions. i.e. if the last parameter (highest number) is
displayed, a further press will cause the display to rollover and show the first parameter mm00. Similarly if the last menu (highest letter) is
displayed, a further press will cause the display to rollover and show the first menu (User Menu A).
Figure 5-5 Menu parameter structure
5.7 Keypad menu and parameter shortcuts
The keypad shortcuts in ‘parameter mode’ allow the user to move quickly within the menus and parameters using the navigation keys. The parameter
value in edit mode can also be accessed much faster using the navigation keys also as detailed following.
• Menu shortcut
If the left and right navigation keys are pressed together, then the keypad display will jump to User Menu A from the current menu being
viewed, i.e. menu G Profile is being viewed when the above keys are pressed together the display will jump directly to User Menu A.
• Parameter shortcut
If the up and down navigation keys are pressed together, then the keypad display will jump to the first parameter 00 in the menu being
viewed, i.e. Menu B Motor and parameter 05 Motor Number Of Poles is being viewed, when the above keys are pressed together the display will jump
to Menu B Motor and parameter 00.
e
Pa
a
rm
t
N
c
t
M
o
t
o
r
e
r
o
o
n
i
r
1
0
E
l v
ea
o
s
p
d
U
A
t
r
1
0
E
l v
ea
o
s
p
d
A
t
r
1
0
E
l v
ea
o
s
p
d
n
A
t
Mo
n
it
o
r
i
n
g
A
07
O
u
t
p
u
t
P
o
w
e
r
0
.
000
k
W
r
1
0
E
l v
ea
o
s
p
d
U
A
t
r
1
0
E
l v
ea
s
p
d
A
t
r
1
0
E
l v
ea
p
s
p
d
n
A
Mo
n
it
o
r
n
g
A
06
t
u
0
/
l
a
S
p
A
c
d
s
mm
r
1
0
E
l v
ea
o
s
p
d
U
A
t
r
1
0
E
l v
ea
s
p
d
A
r
1
0
E
l v
ea
p
s
p
d
n
A
Mo
n
it
o
r
i
n
g
A
05
r
0
e
c
P
e
%
n
t
a
g
e
L
o
a
d
A
pp
.
M
e
n
u
3
Z
00
P
a
r
a
m
e
t
e
r
mm
00
N
o
A
c
t
i
o
n
i
B
00
mm
00
A
Navigate through menus
A User Menu
00 Parameter
01 Parameter
02 Parameter
03 Parameter
04 ....
05 ...
06 ..
.. ...
.. ...
xx xxx
B Motor
00 Parameter
01 Drive cntrl m
02 Motor rated
03 Motor rated
04 ....
05 ...
06 ..
.. ...
.. ...
xx xxx
C Encoder
00 Parameter
01 Enc type
02 Enc auto co
03 Enc lines p
04 ....
05 ...
06 ..
.. ...
.. ...
xx xxx
Z User Menu setup
00 Parameter
01 Parameter
02 Parameter
03 Parameter
04 ....
05 ...
06 ..
.. ...
.. ...
xx xxx
Navigate through
parameters