Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
User Menu A Commissioning
Advanced
Parameters
Diagnostics Optimization CT MODBUS RTU Technical Data
352 E300 Design Guide
Issue Number: 1
This is the profile generator output acceleration rate, and is set in mm/s
2
.
This indicates deceleration distance in mm, which is derived from the Profile generator output position and the target stopping position or the creep
speed.
In Creep to floor, this indicates the distance used in the decelerating state, Elevator Software State (J03) = 9, which is the distance used to get from
the speed at the time the deceleration state was entered to the creep speed. If floor sensor correction is triggered during the deceleration state then
this shows the distance to a stop instead of the creep speed.
In Direct to floor, Elevator Control Mode (H19) = Direct To Floor (1), this indicates the distance used in the decelerating state, Elevator Software State
(J03) = 9, which is the distance used to get from the speed at the time the deceleration state was entered to a stop.
This is not available when an analog reference is selected, Control Input Mode (H11) = Analog Run Prmit or Analog 2 Dir (0 or 1).
This indicates the sampled profile deceleration distance in mm, for the selected speed, V1 Speed Reference (G01) to V10 Speed Reference (G10),
which is derived from the profile setup parameters in the Profile menu.
When only V1 Speed Reference (G01) is selected this shows the distance from the creep speed to zero speed. When V2 Speed Reference (G02) to
V10 Speed Reference (G10) is selected this shows the distance from the selected speed to V1 Speed Reference (G01).
In Direct to floor, Elevator Control Mode (H19) = Direct To Floor (1), this shows the distance from the selected speed, V1 Speed Reference (G01) to
V10 Speed Reference (G10) to zero speed.
This is not available when an analog reference is selected, Control Input mode (H11) = Analog Run Prmit or Analog 2 Dir (0 or 1).
This indicates measured deceleration distance in mm, which is derived from the feedback position sampled when deceleration begins to when the
elevator motor stops or reaches the creep speed.
In Creep to floor, this indicates the distance used in the decelerating state, Elevator Software State (J03)
= 9, which is the distance used to get from
the speed
at the time the deceleration state was entered to the creep speed. If floor sensor correction is triggered during the deceleration state then
this shows the distance to a stop instead of the creep speed.
In Direct to floor, Elevator Control Mode (H19) = Direct To Floor (1), this indicates the distance used in the decelerating state, Elevator Software State
(J03) = 9, which is the distance used to get from the speed at the time the deceleration state was entered to a stop.
In RFC-A and RFC-S:
This is based on the actual encoder position feedback.
J41 Reference Acceleration
Mode Open-Loop, RFC-A, RFC-S
Minimum 0 Maximum 10000
Default Units mm /s²
Type 16 Bit Volatile Update Rate Background
Display Format Standard Decimal Places 0
Coding RO, ND, NC, PT
J42 Deceleration Distance
Mode Open-Loop, RFC-A, RFC-S
Minimum 0 Maximum 32767
Default Units mm
Type 16 Bit Volatile Update Rate Background
Display Format Standard Decimal Places 0
Coding RO, ND, NC, PT
J43 Deceleration Distance Calculated
Mode Open-Loop, RFC-A, RFC-S
Minimum 0 Maximum 10000
Default Units mm
Type 16 Bit Volatile Update Rate Background
Display Format Standard Decimal Places 0
Coding RO, ND, NC, PT
J44 Deceleration Distance Measured
Mode Open-Loop, RFC-A, RFC-S
Minimum 0 Maximum 32767
Default Units mm
Type 16 Bit Volatile Update Rate Background
Display Format Standard Decimal Places 0
Coding RO, ND, NC, PT
To Next Page
Loading...
