Types 67, 67H, 67HR, 67R, 67SS, and 67SSR
7
Key Description Part Number
21 Pipe Plug (for use only w/2-outlet
body—not shown)
For Type 67 or 67R
Hex head to provide sour gas corrosion
resistance capability, pl steel 1D754828982
For other than sour gas corrosion resistance
applications
Square head, brass 1A572614012
Socket head, steel 1C333528992
Hex head, pl steel 1D754828982
For Type 67H or 67HR
Square head, brass 1A572614012
Socket head, steel 1C333528992
Hex head, pl steel 1D754828982
For Type 67SS or 67SSR, 316 stainless steel 1A767535072
21 Pressure Gauge (for use only
w/2-outlet body—not shown)
0 to 30 psig
(3)
1J946099012
0 to 60 psig
(3)
1J975299012
0 to 100 psig
(3)
1J975399012
0 to 160 psig
(3)
1J975499012
23* Body Plug O-Ring (for use only w/Type
67SS or 67SSR)
For use w/composition diaphragm,
composition 1F113906992
For use w/fluoroelastomer diaphragm,
fluoroelastomer 1N463906382
Key Description Part Number
24 Inlet Screen Assembly (for use only when specified)
For Type 67 or 67R
Brass and stainless steel 1C7712000A2
Steel and stainless steel 1C7712000B2
For Type 67H or 67HR, brass and
stainless steel 1C7712000A2
For Type 67SS or 67SSR, steel and
stainless steel 1C7712000B2
28 Closing Cap
For use only w/Type 67 or 67R tapped
spring case 10A3075X012, brass 1H236914012
For use only w/Type 67SS or 67SSR spring case
Aluminum 1H2369X0012
Steel 1H2369X0022
Stainless steel 1H2369X0032
32* Closing Cap Gasket, (for use only
w/Type 67SS or 67SSR), composition 15A6218X012
38 Spacer (for yoke mtg only—not shown),
steel (3 req’d) 11A8146X012
39 Mounting Bracket (for yoke mtg only—
not shown), steel 21A8145X012
44 NACE Tag (for use only w/Type 67 or
67R w/sour gas corrosion resistance
capability—not shown), 18-8 stainless steel 19A6034X012
45 Tag Wire (for use only w/NACE tag key
44—not shown), 304 stainless steel 1U7851X0012
47 Vent Screen (for use only w/Type
67SS or 67SSR spring case
28A9277X012), Monel
(2)
0L078343062
Figure 2. Type 67 and 67R Regulator Assemblies (Also Typical of Types 67H and 67HR) (continued)
1-HOLE PANEL MOUNTING DETAIL 3-HOLE PANEL MOUNTING DETAIL
2
1
0.12 (3,2)
MINIMUM PANEL
THICKNESS
0.39 (9,9)
THREAD
LENGTH
DRILL 0.10 (4,9)
HOLES FOR 10-24
SCREW SIZE
2.08
(53)
2
1
NOTE:
0.72 (18,3) SPRING CASE PANEL BOSS.
1.47 TO 1.48 (37,4 TO 37,7) SPRING CASE PANEL BOSS.
To Next Page
Loading...
