Emerson Rosemount 5300 Series - Page 377

Emerson Rosemount 5300 Series

488 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Figure B-2: 9240030-937 - Installation Drawing for Hazardous Location Installation of Intrinsically Safe

CSA Approved Apparatus

Reference Manual Product certifications

00809-0100-4530 April 2019

Reference Manual 377

Table of Contents

Default Chapter5
- Table of Contents5
Chapter 1 Introduction9
- Using this Manual9
- Product Recycling/Disposal10
Chapter 2 Transmitter Overview11
- Theory of Operation11
- Application Examples12
- Components of the Transmitter14
- System Integration16
- Probe Selection Guide19
- Measuring Range21
- Process Characteristics23
- Vessel Characteristics25
Chapter 3 Mechanical Installation27
- Safety Messages27
- Mounting Considerations28
- Shorten the Probe44
- Centering Disc for Pipe Installations60
- Mount Device on Tank67
- Anchor the Probe88
Chapter 4 Electrical Installation93
- Safety Messages93
- Cable/Conduit Entries94
- Grounding94
- Cable Selection95
- Hazardous Areas96
- 4-20 Ma/Hart96
- Hart99
- To Modbus ® Converter (HMC)99
- FOUNDATION ™ Fieldbus105
- Connect Wiring and Power up107
- Optional Devices110
Chapter 5 Configuration113
- Safety Messages113
- Overview113
- Host System Integration115
- Establish HART ® Communication for Transmitter with HART to Modbus ® Converter119
- Basic Configuration Using Rosemount Radar Master122
- Basic Configuration Using AMS Device Manager and Handheld Communicator139
- Basic Configuration Using Deltav140
- Foundation140
- OUNDATION Fieldbus Overview144
- Modbus ® Communication Protocol Configuration147
- Configure the Alarm Output for the Modbus ® Transmitter153
- HART ® Multi-Drop Configuration156
Chapter 6 Operation159
- Safety Messages159
- Using the Display Panel160
- Specify Display Panel Variables161
- View Measurement Data165
Chapter 7 Service and Troubleshooting169
- Safety Messages169
- Diagnostic Messages171
- LCD Error Messages177
- LED Error Messages178
- FOUNDATION ™ Fieldbus Error Messages180
- Troubleshooting Guide183
- Diagnostics189
- Level and Distance Calibration192
- Service and Troubleshooting Tools194
- Application Challenges224
- Upgrade the HART ® to Modbus ® Converter Firmware Using Rosemount Radar Master234
- Replace the Transmitter Head237
- Changing a Probe238
- Service Support242
- Safety Instrumented Systems (4-20 Ma Only)245
  - Safety Messages245
Chapter 8 Safety Instrumented Systems (4-20 Ma Only)245
- Terms and Definitions246
- Safety Instrumented System (SIS) Certification246
- Safety-Certified Identification247
- Installation in SIS Applications248
- Configuring in SIS Applications249
- Perform Proof Test for SIS Applications251
- Inspection267
- Specifications268
Appendix A Specifications and Reference Data271
- Performance Specifications271
- Functional Specifications280
- Physical Specifications300
- Dimensional Drawings307
- April308
- Proprietary Flanges324
- Flushing Connection Rings325
- Ordering Information326
- Spare Parts and Accessories343
Appendix B Product Certifications359
- European Directive Information359
- Safety Instrumented Systems (SIS)359
- Ordinary Location Certification359
- Installing Equipment in North America359
- Usa359
- Canada361
- Europe362
- International364
- Brazil367
- China368
- Technical Regulations Customs Union (EAC)369
- Japan370
- Republic of Korea370
- India371
- Ukraine371
- Uzbekistan371
- Combinations372
- Additional Certifications372
- Pattern Approval374
- Conduit Plugs and Adapters374
- Installation Drawings376
Appendix C Configuration Parameters381
- Menu Tree381
- Basic Configuration Parameters385
Appendix D Advanced Configuration397
- Safety Messages397
- User Defined Upper Reference Point397
- Probe End Projection398
- Adjust the Echo Tracking Settings402
- Dielectric Constant Settings403
- Dynamic Vapor Compensation405
- Signal Quality Metrics414
- Switch Alarm Limits (HART ® Only)417
- Detecting Thin Interface Layers418
Appendix E Remote Mounting421
- Remote Housing, New Units421
- Remote Connection, Field Retrofit421
- Install Remote Housing422
- Remote Housing Configuration in Rosemount Radar Master424
Appendix F Level Transducer Block425
- Overview425
- Parameters and Descriptions426
- Supported Units433
- Diagnostics Device Errors435
Appendix G Register Transducer Block437
- Overview437
- Register Access Transducer Block Parameters437
Appendix H Advanced Configuration Transducer Block441
- Overview441
- Advanced Configuration Transducer Block Parameters441
Appendix I Resource Transducer Block445
- Overview445
- Parameters and Descriptions445
- Alerts450
- Alarm Priority452
- Process Alarms453
- Recommended Actions for Alerts453
Appendix J Analog-Input Block457
- Analog Input Block457
- Simulation461
- Damping461
- Signal Conversion462
- Block Errors463
- Modes464
- Alarm Detection464
- Advanced Features465
- Configure the AI Block466
Appendix K Rosemount 5300 with HART to Modbus Converter473
- Safety Messages473
- Introduction474
- Workflow for Commissioning a Transmitter with Modbus Protocol475
- Common Modbus ® Host Configuration476
- Specific Modbus ® Host Configuration480

Other manuals for Emerson Rosemount 5300 Series

Quick Start Guide56 pages

Product Data Sheet52 pages

Related product manuals

Emerson Rosemount 5302

Emerson Rosemount 5301

Preview: Emerson Rosemount 56

Emerson Rosemount 56

Preview: Emerson Rosemount 520

Emerson Rosemount 520

Preview: Emerson Rosemount 5408

Emerson Rosemount 5408

Preview: Emerson Rosemount 5402

Emerson Rosemount 5402

Preview: Emerson ROSEMOUNT 5081-A

Emerson ROSEMOUNT 5081-A

Preview: Emerson Rosemount 5081-T

Emerson Rosemount 5081-T

Preview: Emerson Rosemount 5400 Series

Emerson Rosemount 5400 Series

Preview: Rosemount Analytical HART 5081-A-HT

Rosemount Analytical HART 5081-A-HT

Preview: Emerson Rosemount 702

Emerson Rosemount 702

Preview: Emerson Rosemount 1056

Emerson Rosemount 1056