61
60
TEKNISET TIEDOT
Kuvaus
Valmistaja EMS SA, CH-1260 Nyon, Sveitsi
Malli AIR-FLOW handy 3.0 PERIO
Luokitus 93/42/ETY Luokka IIa
Tila Jatkuva käyttö
Syöttöpaine turbiiniliitäntään:Vesi
1- 2.2 baaria (1000-2200 hPa)
syöttövirtauksella 50-80 ml/min.
Syöttöpaine turbiiniliitäntään:Ilma
Staattinen paine 2.7 - 3.5 baaria
(2700-3500 hPa)
Paino Noin 0,150 kg
Käyttöolosuhteet +10°C - +40°C
suhteellinen kosteus 30 % - 75 %
ilmanpaine 700 hPa - 1060 hPa
Korkeus enintään 3000 m
Käsikappaleen vahvistettu käyttöikä 800 sterilointisykliä
Varastointiolosuhteet -10°C - +40°C
suhteellinen kosteus 10 % - 90 %
ilmanpaine 500 hPa - 1060 hPa
Kuljetusolosuhteet -10°C - +40°C
suhteellinen kosteus 10 % - 90 %
ilmanpaine 500 hPa - 1060 hPa
TECHNICAL DATA
Description
Manufacturer EMS SA, CH-1260 Nyon, Switzerland
Model AIR-FLOW
handy 3.0 PERIO
Classication 93 / 42 EEC Class IIa
Mode Continuous operation
Service Pressure to the turbine
connection : Water
1 to 2.2 bar (1000-2200 hPa)
with a service ow of 50-80 ml/min.
Service Pressure to the turbine
connection : Air
Static pressure 2.7 to 3.5 bar
(2700-3500 hPa)
Weight Approx. 0.150 kg
Operating conditions +10°C to +40°C
30% to 75% relative humidity
700 hPa to 1060 hPa air pressure
Altitude max. 3000 m
Validated life time of the handpiece 800 sterilization cycles
Storage conditions -10°C to +40°C
10% to 90% relative humidity
500 hPa to 1060 hPa air pressure
Transport conditions -10°C to +40°C
10% to 90% relative humidity
500 hPa to 1060 hPa air pressure
Symptom Solutions
Water comes into the powder chamber
or leaks from the cap
• Check the dental unit connection
• Check the state of the o-rings of the turbine connection
• Connect the unit to the dental unit (be careful, the powder chamber must be empty)
• Dry and ll the powder chamber
• Send the unit to an approved EMS repair center
No powder/air jet coming from the unit
• Cut immediately the air input by releasing the foot pedal
• Wait for 1-2 minutes for the system to decompress
• Disconnect the unit from the dental unit
• Press the foot control pedal of the dental unit
• if no air comes out of the turbine connector, it is your dental unit that causes the problem
• If air comes out, it is the device that causes the problem
• Unscrew the cap above the wash-hand basin, because the powder can be ejected. A sealed apparatus, even
disconnected, can indeed remain under pressure
• Empty the powder chamber and screw the cap back on
• Connect the unit to the dental unit (be careful, the powder chamber must be empty)
• Connect the handpiece to the unit
• Press the foot control pedal of the dental unit
• If air comes through the handpiece connector, the handpiece is blocked. Clean the handpiece
• If no air comes out of the handpiece connector, the unit is blocked
• Send the unit to an approved EMS repair center
No water spray is coming from the
nozzle
• Change the nozzle
• Remove the nozzle and verify that a water jet comes out from the handpiece
• Send the device to a certied EMS Repair Center
Water leakage between the
handpiece and the nozzle
(unusual leak of droplets)
• Check the position of the nozzle and its position on the handpiece
• Change the nozzle
• Check for residues between the nozzle and the handpiece
• Check that nothing aects the alignment of the nozzle
• Send the device to a certied EMS Repair Center
Water leakage between the nose
connection and handpiece
• Check the O-rings on the nose connection of the device, replace them if necessary
• Change the handpiece
• Send the device to a certied EMS Repair Center
Air and/or powder is leaking from the
threads of the cap
• Check the seal and the cleanliness of the thread on the powder chamber and on the cap
• Replace the seal or the cap if necessary
• Send the device to a certied EMS Repair Center
TROUBLESHOOTING
To Next Page
Loading...
