Fastlane
®
Swim Unit Installation
Section 14 USING YOUR FASTLANE
Two wireless transmitters are included with the Fastlane shipment which are used to turn the unit On/Off
and adjust the speed of the swim current. Press and hold the On/Off button (middle power button) to turn
the unit on. Press and hold the faster button (up arrow) to increase the speed of the swim current. Press and
hold the slower button (down arrow) to decrease the speed of the swim current. Turn the unit off by press-
ing and holding the On/Off button.
The hydraulic power unit controller is equipped with a built-in timer, shutting the unit off after 30 minutes.
The Fastlane will “remember” the speed of the swim current at which it was turned off and will default to
that same speed when the unit is turned back on.
Section 15 GENERAL INFORMATION
Once installed, the Fastlane will provide years of exercise and fun with minimal maintenance. Clean the
intake grills of leaves as needed and wipe down the stainless steel cylindrical base and grab rail with warm
water, a Scotch Brite pad, and brisk rubbing. Clean the acrylic housing with any typical non-ammonia,
non-abrasive kitchen cleanser. Periodically, check all electrical and ground wire connections and test the
GFCI circuit breaker for proper function.
It is important for the long-term operation of your Fastlane that your pool water be properly balanced and in
accordance with normal pool industry standards. In addition, it is imperative that the Fastlane be bonded to
the pool bonding grid.
Endless Pools is an industry leader in customer service, should you ever have questions or concerns about
your Fastlane, please contact our Customer Service Department at 800-910-2714 (US), 0800-520-0196
(UK) or 610-497-4538 (Direct).
Section 16 SCHEDULED MAINTENANCE
16.1 Hydraulic Motor and Fluid Maintenance. We recommend the hydraulic motor, which is located in your
swim unit and submerged underwater, be replaced after six years of usage. We also recommend chang-
ing the non-food grade, biodegradable vegetable oil and lter in the Power Unit after every 500 hours
of use.
16.2 Grill Cleaning. Should you perceive a reduction in speed of your Fastlane, it may be caused by a
reduction in water ow due to a blockage of the inlet assembly of the cylindrical base. Because the
underside of your Fastlane will be drawing in water, it may occasionally become necessary to clean
the cylindrical base of any debris or leaves that may have been in your pool when the Fastlane was in
operation. With the Fastlane unit turned off, this is very easy to accomplish while in the pool.
16.3 Cold Weather Maintenance. At the end of the swimming season, it is recommended the Fastlane Swim
Unit be removed from the swimming pool and winterized. For specic instructions, please contact our
Customer Service Department at 800-910-2714 (US), or 610-497-4538 (Direct).
16.4 Use of Salt-chlorine generators. Placing a Fastlane in a pool sanitized using a salt-chlorine generator
creates increased risk of a hydraulic system failure and oil leaks. Any Fastlane placed in this type of
environment must be properly bonded, and water chemistry must be closely monitored. As stated in
our warranty, pH levels must be maintained between 7.4 and 7.8, total alkalinity between 80 and 120
ppm, salt chlorine levels below 4000 ppm, and total dissolved solids below 7000 ppm. Failure to prop-
erly bond the Fastlane or maintain proper water chemistry will void the warranty.
If you are using a salt-chlorine generator, please complete the following tasks:
• Remove and inspect your Fastlane unit annually. Once removed, rinse the Fastlane with fresh water
before storing for the off-season.
• Replace the underwater hydraulic motor and submersible hoses every two years.
• Ensure that the uid level in your power unit is no more than one cup above the oat level switch.
This simple procedure ensures that any oil leak is minimized
43
To Next Page
Loading...
