Endress+Hauser Analytik Jena Biometra TRIO Series - Running, Pausing, Continuing and Stopping Programs; Display During Run

110 pages

To Next Page

To Previous Page

Running, pausing, continuing and stopping programs Biometra TRIO

58 Version 03_19

9 Running, pausing, continuing and stopping programs

To switch between the view for the sample blocks during run select the number of the

sample block in the corresponding screen.

SAMPLE BLOCK 1

SAMPLE BLOCK 2

SAMPLE BLOCK 3

9.1 Display during run

After a program is started (see chapter "Display during run" p. 58), the Biometra TRIO

software can display the running program in spreadsheet or graphical view. Use the

following buttons to toggle between both modes.

GRAPHICAL VIEW

SPREADSHEET VIEW

Figure 34 Biometra TRIO run screen in graphical view

Main Page

Default Chapter3
- Table of Contents3
1 Basic Information9
- User Manual Notes9
- Intended Use10
- Warranty and Liability10
2 Safety Instructions11
- General Notes11
- Safety Markings on the Biometra TRIO11
- Technical Condition11
- Requirements for the Operating Personnel12
- Safety Instructions: Transport and Installation12
- Safety Instructions - Operation12
- General12
- Safety Instructions: Protection against Explosion and Fire13
- Safety Instructions: Electrical Equipment13
- Handling of Samples, Auxiliary and Operating Materials14
- Safety Instructions - Maintenance and Repair14
- Behavior During Emergencies14
3 Function and Setup15
- Field of Applications15
- General Description15
- Figure 1 Biometra TRIO Thermal Cycler15
- Special Features16
- Thermal Block16
- High Performance Smart Lid16
- Display16
- User-Specific Quick Start Function17
- Easy Programming17
- Temperature Optimisation Step (TOS)17
- GLP Compliance18
- Open System Philosophy18
- Order Numbers18
4 Installation and Commissioning19
- Content of Delivery19
- Unpack and Check19
- Installation Conditions19
- Operation Voltage20
5 Control Elements21
- The Biometra TRIO Front View21
- The Biometra TRIO Rear View21
- Figure 2 Biometra TRIO Front View21
- Figure 3 Biometra TRIO Rear View21
- High Performance Smart Lid (HPSL)22
- Loading Samples22
- Figure 4 Biometra TRIO Lid Open Button22
- The Biometra TRIO Software23
- Keyboard23
- Figure 5 Biometra TRIO Keyboard23
- Keypad24
- Figure 6 Biometra TRIO Keypad24
- Cursor Keys25
- Confirm or Cancel25
- List of Used Commands and Icons25
6 Operating30
- Power on Self-Test30
- Log in Screen30
- Figure 7 Biometra TRIO Start Screen30
- Log in31
- Figure 8 Biometra TRIO Log in Screen31
- Figure 9 Biometra TRIO Select User Screen31
- Home Screen32
- Figure 10 Biometra TRIO Enter Password Screen32
- Figure 11 Biometra TRIO Home Screen32
- Block Status33
- Figure 12 Biometra TRIO Block Status/Quick Start Button33
- Quick Start Function34
- Figure 13 Biometra TRIO Quick Start Screen35
- Incubation Mode36
- Figure 14 Biometra TRIO Multiblock Selection Query36
- Figure 15 Biometra TRIO Incubation Mode Screen37
7 Creating, Editing and Saving Programs39
- Programming Modes39
- Figure 16 Biometra TRIO Spreadsheet Programming39
- Figure 17 Biometra TRIO Graphical Programming Screen39
- Create a New Program/Use Program Template40
- Figure 18 Biometra TRIO Program Overview Screen41
- Figure 19 Biometra TRIO Program Template "Blank41
- Assign Program Names42
- Set Heated Lid Temperature42
- Figure 20 Biometra TRIO Program Template Screen42
- Set Preheating Mode43
- Figure 21 Biometra TRIO Lid Temperature Setting Screen43
- Edit Parameter or Step44
- Set Cycles45
- Figure 22 Biometra TRIO Edit Step Screen45
- Set Temperature Increment46
- Set Time Increment46
- Figure 23 PCR Program with Loop46
- Adjust Ramp Rate47
- Set Temperature Optimisation Step (TOS)47
- Figure 24 Biometra TRIO Temperature Optimisation Step Screen48
- Insert Step49
- Delete Step49
- Save Program49
- Figure 25 Program Overview Screen50
- Figure 26 Quick Selection Screen51
8 Starting, Copying and Deleting Programs52
- Start Program52
- Figure 27 Biometra TRIO Program Overview Screen52
- Copy Program53
- Figure 28 Biometra TRIO Program Overview Screen with Program Preview53
- Figure 29 Biometra TRIO Multiblock Selection Query53
- Figure 30 Biometra TRIO Program Overview Screen54
- Copy All Programs55
- Figure 31 Biometra TRIO Program Overview Screen55
- Delete Program56
- Delete All Programs56
- Figure 32 Biometra TRIO Security Query56
- Figure 33 Biometra TRIO Security Query57
9 Running, Pausing, Continuing and Stopping Programs58
- Display During Run58
- Figure 34 Biometra TRIO Run Screen in Graphical View58
- Pause Program59
- Figure 35 Biometra TRIO Run Screen in Spreadsheet View59
- Continue Program60
- Skip Step60
- Figure 36 Biometra TRIO Run Screen During Program Pause60
- Stop Program61
- Figure 37 Biometra TRIO Query for Multiblock Selection61
- Figure 38 Biometra TRIO Security Query61
10 Protocol Wizard62
- Select Polymerase62
- Enter New Polymerase or Edit Polymerase62
- Figure 39 Biometra TRIO Polymerase Selection Screen62
- Figure 40 Biometra TRIO Screen for Editing Program Templates for Polymerases63
- Delete Polymerase64
- Figure 41 Biometra TRIO for Saving Program Templates for Polymerases64
- Figure 42 Biometra TRIO Security Query64
- Protocol Wizard Parameter Screen65
- Figure 43 Biometra TRIO Protocol Wizard Parameter Screen65
- Primer Annealing Temperature Calculator66
- Figure 44 Biometra TRIO Protocol Wizard View Parameter Screen66
- Figure 45 Biometra TRIO Security Query66
- Figure 46 Biometra TRIO Primer Annealing Temperature Calculator Screen67
- Figure 47 Biometra TRIO Screen for Primer Concentration Adjustment68
11 Tools70
- Settings70
- Figure 48 Biometra TRIO Tools Screen70
- Set Date and Time71
- Figure 49 Biometra TRIO Settings Screen71
- Automatic User Logout72
- Figure 50 Biometra TRIO Date and Time Screen72
- Configure Beeper73
- Figure 51 Biometra TRIO Automatic User Logout Screen73
- Network74
- Display Brightness76
- Touch Screen Calibration76
- Factory Settings77
- User Management78
- Create User80
- Edit User81
- Delete User84
- Documentation84
- Run-Logfile85
- Power-On-Logfile87
- Extended Self-Test-Logfile88
- Error-Logfile89
- Extended Self-Test89
- Service Info File (SINF)92
- Backup92
- Cycler Info93
- Contact94
12 Adaptation of Programs95
13 Short Manual96
14 Fault Removal96
- Forgotten Password100
- Slow Heating and Cooling100
- Auto Restart100
- Auto Restart Due to Unrecognized Power Failure100
- Mirror Programs to Several Thermal Cyclers101
- Adapt Protocols from Other Cyclers101
- Release Wheel in Case of Blocked Lid101
15 Maintenance and Repair102
- Factory Calibration102
- Servicing and Repair102
- Cleaning102
- Disinfecting the Device103
- Firmware Update103
- Spare Parts103
16 Service104
- Instructions for Return Shipment104
- Packing of the Biometra TRIO Thermal Cycler105
17 Disposal106
18 Technical Specifications107
19 Declaration of Conformity109
20 Index110

Endress+Hauser Analytik Jena Biometra TRIO Series - Running, Pausing, Continuing and Stopping Programs; Display During Run

Table of Contents

Related product manuals