EasyManua.ls Logo

Endress+Hauser iTEMP TMT162 - Product Structure; Ordering Information

Endress+Hauser iTEMP TMT162
24 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
TMT162
Endress+Hauser 19
Ordering information
Product structure
TMT162 iTEMP
®
TMT162, Field transmitter, Temperature transmitter; Application: RTD, TC, Ohm, mV; 2-wire 4...20 mA; galvanic
isolation; NEMA 4x, IP67; Dual compartment; GL (German Lloyd) Marine (HART
®
device only); UL listed
Approval:
A Non-hazardous area
B ATEX II1G EEx ia IIC T4/T5/T6
C FM IS, NI I/1+2/A-D
D CSA IS, NI I/1+2/A-D
E ATEX II2G EEx d IIC T6
F FM XP, DIP I,II,III/1+2/A-G
G CSA XP, DIP I,II,III/1+2/A-G
H ATEX EEx d, EEx ia
J FM XP, DIP, IS, NI I,II,III/1+2/A-G
K CSA XP, DIP, IS, NI I,II,III/1+2/A-G
L ATEX II3G EEx nA IIC T4/T5/T6
M FM + CSA XP, DIP, IS, NI, I,II,III/1+2/A-G
N ATEX II1/2D
O CSA General Purpose
P IECEx Ex ia IIC T6/T5/T4
R IECEx Ex d IIC T6/T5/T4
S IECEx Ex ia Ex d IIC T6/T5/T4
T ATEX II1/2GD EEx ia IIC T4/T5/T6
1 NEPSI Ex ia IIC T4-T6
2 NEPSI Ex nA II T4-T6
3 NEPSI Ex d IIC T4-T6
4 TIIS Ex ia IIC T4
5 TIIS Ex ia IIC T6
6 TIIS Ex d IIC T6
Housing:
1 Alu, w/o display
2 Alu + display, illum.
3 316L, w/o display
4 316L + display, illum.
5 T17, 316L, w/o display
6 T17, 316L + display, illum.
Cable Entry:
A 2x thread NPT1/2, 1x plug M12 PA
1)
1) Fieldbus connector is pre-assembled and wired at factory
B 2x thread M20x1.5, 1x plug M12 PA
1)
, 1x gland M20
C 2x thread NPT1/2 1x plug 7/8" FF
1)
D 2x thread M20x1.5, 1x plug 7/8" FF
1)
, 1x gland M20
E 2x thread M20x1.5, 1x plug 7/8" PA
1)
, 1x gland M20
1 2x thread NPT ½“
2 2x thread M20x1.5
4 2x thread G½“
5 1x thread M24x1.5 + 1x M20x1.5
6 2x gland M20x1.5
Mounting Bracket:
1 Not selected
2 Wall / pipe 2", L-shape, 304
3 Pipe 2", U-shape, 316L
Configuration Connection:
A Factory setup
1 Thermocouple TC
2 RTD 2-wire
3 RTD 3-wire
4 RTD 4-wire
Configuration Sensor Type:
A Factory setup
1 Pt100 (-200 to 850 °C, -328 to 1562 °F, min. span 10 K, 18 °F), as per IEC 60751
2 Ni100 (-60 to 250 °C, -76 to 482 °F, min. span 10 K, 18 °F)
3 Pt500 (-200 to 250 °C, -328 to 482 °F, min. span 10 K, 18 °F)
4 Pt100 (-200 to 649 °C, -328 to 1200 °F, min. span 10 K, 18 °F) as per JIS C1604-81

Other manuals for Endress+Hauser iTEMP TMT162

Related product manuals