Endress+Hauser iTEMP TMT82 - Page 113

iTEMP TMT82 Index
Endress+Hauser 113
HART® protocol
Device variables .......................... 30
Operating tools .......................... 30
Version data for the device .................. 30
L
Linearization (submenu) ...................... 97
Locking status ..............................71
Lower range value (parameter) ................. 69
M
Mains filter (parameter) ...................... 94
Manufacturer ............................. 111
Manufacturer ID (parameter) ..............103, 111
Measured values (submenu) ............... 90, 111
Measuring mode (parameter) .............. 75, 101
Min/max values (submenu) ....................90
Mounting location
DIN rail (DIN rail clip) ......................11
Field housing ............................ 11
Terminal head, flat face as per DIN 43729 ...... 11
N
Nameplate ................................. 8
No. of preambles (parameter) ................. 102
O
Operating time ............................. 86
Operation options
Local operation .......................... 22
Operating tool ........................... 22
Overview ............................... 22
Operational state (parameter) .................. 81
Order code ................................ 89
Out of range category (parameter) ...............76
Output (submenu) ..........................101
Output current ............................. 75
P
Polynomial coeff. A, B (parameter) .............. 99
Polynomial coeff. R0 (parameter) ................99
Previous diag channel ........................ 88
Previous diagnostics ......................... 88
Previous diagnostics 1 ........................ 86
PV ..................................... 105
Q
QV ..................................... 106
R
Remedy information ......................... 86
Reset configuration changed flag (parameter) ..... 102
Reset device temp. min/max values (parameter) .....92
Reset sensor min/max values (parameter) ......... 91
Return ................................... 43
RJ preset value (parameter) .................... 68
S
Sensor (submenu) ........................ 72, 95
Sensor 1/2 (submenu) ........................95
Sensor lower limit ........................... 95
Sensor lower limit (parameter) ................. 98
Sensor max. value ........................... 91
Sensor min value ............................90
Sensor offset (parameter) ..................... 72
Sensor raw value ...........................111
Sensor switch set point (parameter) ..............74
Sensor trimming (parameter) .................. 96
Sensor trimming (submenu) ................... 96
Sensor trimming lower value (parameter) ......... 96
Sensor trimming min span .....................97
Sensor trimming upper value (parameter) ......... 97
Sensor type (parameter) ...................... 66
Sensor upper limit ........................... 95
Sensor upper limit (parameter) ................. 98
Sensor value ............................... 90
Serial no. sensor (parameter) ...................95
Serial number .............................. 89
Setup (menu) .............................. 66
SIL (submenu) ..............................81
SIL checksum (parameter) ..................... 82
SIL HART mode (parameter) ................... 83
SIL option (parameter) ....................... 81
SIL startup mode (parameter) .................. 83
Simulation (submenu) ........................92
Simulation current output (parameter) ............92
Solid wire ................................. 19
Structure of the operating menu ................ 23
SV ..................................... 105
SWRev .................................. 104
System (submenu) ...........................94
System components ..........................35
T
Terminal assignment .........................17
Timestamp SIL configuration (parameter) ......... 83
Troubleshooting
Application error with RTD sensor connection .... 38
Application error with TC sensor connection ..... 38
Checking the display .......................37
General errors ........................... 37
TV ..................................... 106
U
UL approval ............................... 59
Unit (parameter) ............................66
Upper range value (parameter) ................. 69
V
Value 1 display (parameter) ....................78
Value 2 display (parameter) ....................79
Value 3 display (parameter) ....................80
Value current output (parameter) ............... 92
W
Wire without wire end ferrule .................. 19