Endress+Hauser Levelflex FMP55 HART - Page 194

Index
194 Endress+Hauser
E
Electrical connection
Commubox FXA291 .......................50
Operating tools
Via service interface (CDI) ................ 50
Electronics housing
Design ................................. 15
Turning
see Turning the transmitter housing
Empty calibration (Parameter) .................113
Enter access code (Parameter) ................. 123
Envelope curve display ........................66
Event history ...............................85
Event level
Explanation ............................. 79
Symbols ................................79
Event list (Submenu) ........................175
Event logbook (Submenu) .................... 175
Event text ................................. 80
Events list .................................85
Extended order code 1 to 3 (Parameter) ..........177
Exterior cleaning ............................88
F
Failure current (Parameter) ...................153
Failure mode (Parameter) ................ 152, 158
FHX50 ................................... 49
Filter options (Parameter) .................... 175
Filtering the event logbook .................... 85
Firmware version (Parameter) .................176
Fixed current (Parameter) .................... 152
Flange ................................... 30
Format display (Parameter) ...................160
Free text (Parameter) ....................... 136
Full calibration (Parameter) ...................114
FV (HART device variable) .....................67
H
Hardware write protection .....................56
HART device variables ........................ 67
HART loop converter HMX50 ...................41
HART protocol ............................. 49
HART-Integration ........................... 67
Header (Parameter) ........................ 163
Header text (Parameter) ..................... 164
Heartbeat (Submenu) ....................... 192
Heat insulation ............................. 29
HMX50 ...................................41
Housing
Design ................................. 15
I
Input mask ................................ 63
Interface (Parameter) ....................... 117
Interface (Submenu) ........................ 124
Interface distance (Parameter) .............118, 179
Interface linearized (Parameter) ............137, 180
Interface measurement configuration .............70
Interface property (Parameter) ................ 124
Interface signal (Parameter) .................. 191
Intermediate height (Parameter) ............... 138
Invert output signal (Parameter) ............... 158
K
Keypad lock
Disabling ............................... 58
Switch-on .............................. 58
L
Language (Parameter) .......................160
Last backup (Parameter) ..................... 166
Last check time (Parameter) .................. 190
Launch signal (Parameter) ....................191
Level (Parameter) ...................... 115, 140
Level correction (Parameter) .................. 127
Level linearized (Parameter) .............. 136, 179
Level signal (Parameter) ..................... 191
Level unit (Parameter) .......................126
Linearization (Submenu) ............. 132, 133, 134
Linearization type (Parameter) ................ 134
Local display ............................... 48
see Diagnostics message
see In alarm condition
Locking status (Parameter) ................... 122
Logging interval (Parameter) ..................183
M
Maintenance ...............................88
Manage device configuration ...................75
Manual thickness upper layer (Parameter) .... 127, 130
Manufacturer ID (Parameter) ................. 178
Mapping (Wizard) ..........................121
Mapping end point (Parameter) ............120, 121
Maximum value (Parameter) ..................137
Measured current 1 (Parameter) ............... 181
Measured materials ..........................12
Measured thickness upper layer (Parameter) ...... 128
Measured value symbols ...................... 61
Measured values (Submenu) .................. 179
Medium group (Parameter) ................... 113
Menu
Diagnostics ............................ 172
Setup .................................111
Mounting position for interface measurements ..... 21
N
Number format (Parameter) .................. 164
O
Operating elements
Diagnostics message .......................80
Operating mode (Parameter) ..................111
Operating module ........................... 59
Operating time (Parameter) ...............166, 173
Operating time from restart (Parameter) ......... 173
Operational safety ...........................13
Order code (Parameter) ......................177
Output current 1 to 2 (Parameter) .......... 153, 181
Output echo lost (Parameter) ..................142