C
A1
A4A3
A5 A6
A
B
Z Z4
O332
B5
Z5
O333
B1
Z1
B2*
Z2
O3(3)
B3
Z3
O331
B4
O3(2)
O321
O O1 O2 O3(1) O311 O312 O313
C35
C25
C15
C26
C32
C22
C12
C33
C23
C13
C34
C24
C14
C31
C21
C11
Z6
A2
C15
C14 C15
CURRENT INPUT
SETUP 2
SETUP 1
CURRENT OUTPUT
Enter value of ORP
buffer
0 ... 1500 mV
Buffer value of last cal.
Meas. value display
ORP (dep. on B1)pH;
1st error is displayed
(if present)
Meas. value display
Temperature display in °F
Meas. value display
pH signal in mV
Other errors are
displayed
(up to max. 10 errors)
Meas. value display
No temp. display
Enter pH value
of first buffer solution
pH 3.50 ... 9.50
Buffer value of last cal.
Controller switch-off
by sample stream
INSOff;
Controller switch-off
by current input
InputOff;
Select meas. parameter
for 2nd current output
pH; ORPmV; Contr°C;
Select current range
0–20 mA4–20 mA;
lin = linear
pH compensation
Manu; AutoOff;
Enter pH value
of second buffer solution
pH 3.50 ... 9.50
Buffer value of last cal.
Slope is
displayed
38.00 ... 65.00 mV/pH
59.16 mV/pH
Switch-off direction
for current input
HighLow;
Zero calibration
yes
(only if A1 = 963)
no;
Enter calibration
temperature
–10 ... +60 °C25.0 °C
Select sensor
140; 141; 240; 241;
963; 120
Select current output
Output2Output1;
Select operating mode
pH; ORP mVOff;
Enter DPD
calibration value
Value of last cal.
Calibrating
Adopt if stable
±1 mV (> 10 s)
Calibrating
Adopt if stable
pH ±0.05 (> 10 s)
Delay for contr.
sw.-off by sample stream
0 ... 2000 s0 s
Delay for controller
sw.-off current input
0 ... 2000 s0 s
Tab = Table
sim = simulation
Manual
pH compensation
pH 4.00 ... 9.00
last comp. value
Delay for contr.
sw.-on by sample stream
0 ... 2000 s0 s
Delay for controller
sw.-on current input
0 ... 2000 s0 s
Enter simulation
value
0 ... 22.0 mA
current value
Select table
options
editread
Enter number of
table pairs
1 ... 101
Select table
pairs
1 ... No. of table pairs
asign
1
Enter correct
process temperature
0 ... 50 °C
current meas. value
Calibrating
Adopt if stable
pH ±0.05 (> 10 s)
Select
digital input 1
Clean Trig.ext.Hold
Switch-off limit
for current input
0 ... 100%50%
Enter temperature
difference (offset)
–5.0 ... + 5.0 °C
current offset
Calibration status is
displayed
Exxxo.k.
Calibration status is
displayed
Exxxo.k.
Enter calibration
results
no; newyes;
Store calibration
result
no; newyes;
Zero point is
displayed
–100 ... +100 mV
Slope is
displayed
min. 25% (3%)
max. 500%
100%
CALIBRATION
ORP mV
(dep. on B1)
CALIBRATION
pH
(dep. on B1)
MEAS. VALUE
DISPLAY
TEMPERATURE
DISPLAY
with
in °C
CALIBRATION
Cl
2
/ ClO
2
Feedforward control
to PID controller
lin = linearOff;
Meas. value display
Sensor current in nA
Edit:
Code 22
Read:
any code
Edit:
Code 22
Read:
any code
Display unit
ppm; ppbmg/l;
Enter 0/4-mA value
0.00 mg/l;
0.00 ppm
0 ppb;
pH 4.00;
0 mV;
0 °C;
0 ... 20 (5) mg/l
; 0 … 20 ppm
0 … 20000 ppb
pH 4 ... 9
0 ... 1500 mV
0 ... 50 °C
Enter 20-mA value
2.0 (0.5);
2.0 ppm;
2000 ppb;
pH 9.00;
1000 mV;
50 °C;
0 ... 20 (5) mg/l
0 … 20 ppm
0 … 20000 ppb
pH 4 ... 9
0 ... 1500 mV
0 ... 50 °C
* field B2 not available for CCS240/241
CALIBRATION
zero
(CCS120)
Zero calibration
yes
(only if A1 = 120)
no;
Calibration status is
displayed
Exxxo.k.
Store calibration
result
no; newyes;
Operating matrix version EP
To Next Page
Loading...
