Endress+Hauser Proline Promag 53H - Page 53

Proline Promag 50H, 53H
Endress+Hauser 53
Clamp according to
ISO 2852, Fig. 2
1.4404 (F316L)
Sensor
DN
Fits to
piping
Clamp
ISO 2852
nominal
diameter
di G D L LK L
tot
1)
[mm] ISO 2037/
BS 4825-1
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
A0005544
Order codes: 5*H**-W***********, DKH**-HC**
Surface roughness: R
a
 0.8 m
40 38.0 × 1.6 38.0 35.6 50.5 92.0 68.5 71.0 273
50 51.0 × 1.6 51.0 48.6 64.0 105.0 68.5 83.5 273
65 63.5 × 1.6 63.5 60.3 77.5 121.0 68.5 100.0 273
80 76.1 × 1.6 76.1 72.9 91.0 140.7 99.5 114.0 333
100 101.6 × 2.0 101.6 97.6 119.0 166.7 99.5 141.0 333
125 139.7 × 2.0 139.7 135.7 155.0 198.7 53.0 171.0 300
150 168.3 × 2.6 168.3 163.1 183.0 226.7 53.0 200.0 300
Order codes: 5*H**-W***********+CA/+CB; DKH**-HC**+CA/+CB
Surface roughness +CA: R
a
 0.8 m
Surface roughness +CB: R
a
 0.38 m
40 38.0 × 1.6 38.0 35.6 50.5 99.7 43 71.0 220
50 51.0 × 1.6 51.0 48.6 64.0 112.7 43 83.5 220
65 63.5 × 1.6 63.5 60.3 77.5 127.7 43 100.0 220
80 76.1 × 1.6 76.1 72.9 91.0 140.7 43 114.0 220
100 101.6 × 2.0 101.6 97.6 119.0 166.7 43 141.0 220
1) L
tot
= fitting length
If pigs are used for cleaning, it is essential to take the inside diameters of
measuring tube and process connection (di) into account!
Clamp according to
DIN 32676
1.4404 (F316L)
Sensor
DN
Fits to
piping
di G D L LK L
tot
1)
[mm] EN 10357
(DIN 11850)
[mm] [mm] [mm] [mm] [mm] [mm]
A0005539
Order codes: 5*H**-0***********, DKH**-HD**
Surface roughness: R
a
 0.8 m
40 41 × 1.5 38 50.5 92.0 61.5 71.0 259
50 53 × 1.5 50 64.0 105.0 61.5 83.5 259
65 70 × 2 66 91.0 121.0 68.0 100.0 272
80 85 × 2 81 106.0 140.7 99.0 114.0 332
100 104 × 2 100 119.0 166.7 99.0 141.0 332
125 129 × 2 125 155.0 198.7 53.0 171.0 300
150 154 × 2 150 183.0 226.7 53.0 200.0 300
Order codes: 5*H**-0***********+CA/+CB, DKH**-HD**+CA/+CB
Surface roughness +CA: R
a
 0.8 m
Surface roughness +CB: R
a
 0.38 m
40 41 × 1.5 38 50.5 99.7 43 71.0 220
50 53 × 1.5 50 64.0 112.7 43 83.5 220
65 70 × 2 66 91.0 127.7 43 100.0 220
80 85 × 2 81 106.0 140.7 43 114.0 220
100 104 × 2 100 119.0 166.7 43 141.0 220
1) L
tot
= fitting length
If pigs are used for cleaning, it is essential to take the inside diameters of
measuring tube and process connection (di) into account!
G
di
LK
D
L
G
di
LK
D
L