11 Index
A
Accuracy
Measured error . . . . . . . . . . . . 108
Reference conditions . . . . . . . . . . 108
Repeatability . . . . . . . . . . . . . 109
Adapters (for mounting in the pipe) . . . . . . 14
Alarm (process error) . . . . . . . . . . . . 85
Alarm messages (display) . . . . . . . . . . 92
Alarm output
See Relay 1
Ambient temperature . . . . . . . . . . . 110
Amplifier
Amplifier mode . . . . . . . . . . . . . 76
Delay . . . . . . . . . . . . . . . . . 76
Self checking . . . . . . . . . . . . . . 78
Amplifier board . . . . . . . . . . . . . . 96
Auxiliary input
Assign functions . . . . . . . . . . . . . 69
Electrical connection . . . . . . . . . . . 23
General technical data . . . . . . . . . 107
Start pulse width . . . . . . . . . . . . . 71
B
Barrel (engineering unit) . . . . . . . . . . . 48
Batching contact (Relay 1) . . . . . . . . . . 60
Batching functions
Batching counter . . . . . . . . . . . . 65
Batching quantity . . . . . . . . . . . . 64
Batching time (max.) . . . . . . . . . . . 65
Batching variable . . . . . . . . . . . . 64
Compensation quantity . . . . . . . . . . 65
General information . . . . . . . . . . . 63
Reset batching counter . . . . . . . . . . 65
Starting a batching cycle . . . . . . . 63, 65
Batching pre-contact (Relay 2) . . . . . . . . 60
Bidirectional measuring mode . . . . . . . . 75
Build-up (measuring tube, electrodes)
See Electrode Cleaning Circuitry (ECC)
Bus address . . . . . . . . . . . . . . . 69
C
Cable glands . . . . . . . . . . . . . 21, 112
Cable length (remote version) . . . . . . 20, 109
Cable specifications . . . . . . . . . . . . 27
Calibration factor
Nameplate (factory setting) . . . . . . . . 8
Negative factor . . . . . . . . . . . . . 81
Positive factor . . . . . . . . . . . . . . 81
Cathodic protection . . . . . . . . . . . . 28
CE mark . . . . . . . . . . . . . . . . 113
CIP (cleaning in place) . . . . . . . . . . 110
Code number (enabling programming) . . . . . 78
Commissioning . . . . . . . . . . . . . . 34
Communications board . . . . . . . . . . . 96
Commuwin II program
Electrical connection (Commubox FXA 191) . 33
General information . . . . . . . . . . . 42
Compensation quantity (batching) . . . . . . 65
Conductivity (minimum) of the fluid . . . . . . 111
Connection (electrical)
See Electrical connection
Correct usage . . . . . . . . . . . . . . . 5
Counter
See Totalizer
Creep suppression (low flow cutoff) . . . . . . 72
Current output
Current range (0/4...20 mA) . . . . . . . . 51
Dual range mode (full scale 1-2) . . . . . . 50
Electrical connection . . . . . . . . . . . 23
Failsafe mode . . . . . . . . . . . . . 51
Full scale value 1 . . . . . . . . . . . . 49
Full scale value 2 . . . . . . . . . . . . 51
Nominal current . . . . . . . . . . . . . 52
Simulation . . . . . . . . . . . . . . . 52
Technical data . . . . . . . . . . . . . 108
Time constant . . . . . . . . . . . . . 51
D
Damping
Current output (time constant) . . . . . . . 51
Display . . . . . . . . . . . . . . . . 68
Dangerous substances . . . . . . . . . . . . 6
DAT (data storage module) . . . . . . . 96, 113
Degree of protection . . . . . . . . . . . . 110
Degree of protection (IP Code) . . . . . . . . 21
Diagnosis function . . . . . . . . . . . . . 78
Dimensions
Internal diameter . . . . . . . . . . . . 114
Process connections Promag A . . . . . . 100
Process connections Promag H . . . . . . 103
Promag 33 A . . . . . . . . . . . . . . 99
Promag 33 F (DN 15...300) . . . . . . . . 104
Promag 33 F (DN 350...2000) . . . . . . . 105
Promag 33 H . . . . . . . . . . . . . . 102
Display
Assign process variables . . . . . . . . . 67
Display contrast . . . . . . . . . . . . 68
Display damping . . . . . . . . . . . . 68
Language for displayed text . . . . . . . . 68
Number of significant digits . . . . . . . . 68
Operating elements . . . . . . . . . . . 35
Operation (E+H operating matrix) . . . . . . 36
Rotating (4 x 90°) . . . . . . . . . . . . 19
Documentation, supplementary . . . . . . . 113
Promag 33 11 Index
Endress+Hauser 121
To Next Page
Loading...
