ENSONIQ ASR-X PRO - DDL→Chorus

Insert Effect Parameters
40 ENSONIQ ASR-X Pro UserÕs Guide
Dly4 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
LFO Rate 1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
Controls the four rates of the modulation applied to the
delay time of the chorus.
LFO Shape Triangle, Sine, Sawtooth,
Square, Asym, 16-Step, 8-
Step, 4-Step
Determines the shape that the LFO will use for pitch
modulation.
LFO Phase -180deg to +180deg Controls the relative phase between left and right LFOs.
Chorus Depth 0.0ms to 25.0ms Controls the amount of modulation.
ChorusCenter 0.0ms to 50.0ms Controls the delay time within the chorus, and changes
the tonal character.
Spread (wide stereo to mono) This parameter offers control of the synthesized stereo
field. The farthest counterclockwise setting of the Value
knob offers true stereo, the middle setting forces the left
and the right into the center (mono), and turning the
Value knob fully clockwise inverts the left and right
signal.
22
22
11
11
DD
DD
DD
DD
LL
LL
→FF
FF
ll
ll
aa
aa
nn
nn
gg
gg
ee
ee
rr
rr
Combines four independent controllable digital delays with a flanger.
PP
PP
aa
aa
rr
rr
aa
aa
mm
mm
ee
ee
tt
tt
ee
ee
rr
rr
RR
RR
aa
aa
nn
nn
gg
gg
ee
ee
DD
DD
ee
ee
ss
ss
cc
cc
rr
rr
ii
ii
pp
pp
tt
tt
ii
ii
oo
oo
nn
nn
Dly1 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the first independent delay.
Dly1 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly1 Feedback -99% to +99% Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly1 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly1 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
Dly2 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the second independent delay.
Dly2 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly2 Feedback -99% to +99% Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly2 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly2 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
Dly3 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the third independent delay.
Dly3 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly3 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
Dly4 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the fourth independent delay.
Dly4 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly4 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.