Insert Effect Parameters
44 ENSONIQ ASR-X Pro UserÕs Guide
Dly Levels Uniform, Linear+, Linear-,
Expon.+, Expon.-, Random
Controls the relative levels of the taps.
Dly Max Level 0 to 100 Controls the maximum level that any one tap can attain.
Dly Pan Centered, Alternating, L-
>R, R->L, Center->Out,
Out->Center, Random
Controls the panning of the taps in the stereo field.
Dly Spread 0 to 100 Controls the width of the stereo field. A setting of 0 is
the narrowest (mono)Ña setting of 100 is the widest
(full stereo).
22
22
55
55
DD
DD
ii
ii
ss
ss
tt
tt
→CC
CC
hh
hh
oo
oo
rr
rr
uu
uu
ss
ss
Dist→Chorus combines a distortion with a chorus.
Parameter Range Description
Dist LPF Fc 10Hz to 20.0kHz Filters out high frequencies prior to the distortion.
Dist Offset -99% to +99% Adjusts the balance of even-to-odd-generated
harmonics.
Dist Gain Off, -49.5dB to +48dB Controls the gain going into the distortion effect. This
will boost the signal level up to 48 dB. For more
distortion, use a high input level gain and turn Dist
Volume down to keep the volume under control. For
less distortion, use a low gain input level and a higher
output volume.
Dist Curve Soft, Medium 1, Medium 2,
Hard, Buzz
Selects the type of clipping produced by the distortion.
The curves range from tube-like distortion (Soft) to
nasty distortion (Buzz).
Dist Volume Off, -99dB to 0.0dB Controls the volume of the distortion effect. Generally, if
Distortion Gain is set high, set this parameter lower.
Post VCF Fc 10Hz to 7.10kHz Determines the distortion filter cutoff frequency. Higher
values have a brighter sound. This parameter can be
modulated by any continuous MIDI controller for a
wah-wah pedal effect.
Post VCF Q 1.0 to 40.0 Determines the level and width of the resonant peak at
the filter cutoff point. While the Fc (filter cutoff)
parameter determines where (at what frequency) this
peak will occur, the Q setting controls the sharpness of
the peak.
Dist Dry Lev Off, -49.5dB to 0.0dB Controls the amount of dry signal to be mixed with the
distorted signal.
EQ Input Off, -49.5dB to +24dB Adjusts the input level trim to the EQs to eliminate the
possibility of clipping boosted signals.
LoShelf Fc 10Hz to 20.0kHz Sets the center of the low frequency EQ.
LoShelf Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this low
frequency band.
Mid 1 Fc 10Hz to 20.0kHz Sets the center of the mid frequency parametric.
Mid 1 Q 1.0 to 40.0 This parameter is a bandwidth control that determines
the width of the resonant peak at the center frequency
band. This parameter is equal to the cutoff frequency
divided by the bandwidth. By raising the value, you can
produce a narrower bandwidth.
Mid 1 Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this mid
frequency band.
Mid 2 Fc 10Hz to 20.0kHz Identical to the Mid 1 Fc parameter, and is used to
control different bandwidths within the mid range.
Mid 2 Q 1.0 to 40.0 Identical to the Mid 1 Q parameter, and is used to
control different bandwidths within the mid range.
Mid 2 Gain Off, -49.5dB to +24dB Identical to the Mid 1 Gain parameter, and is used to
control different bandwidths within the mid range.
HiShelf Fc 10Hz to 20.0kHz Sets the center frequency of the high frequency shelf.
To Next Page
Loading...
