Insert Effect Parameters
50 ENSONIQ ASR-X Pro UserÕs Guide
Dist Dry Lev Off, -49.5dB to 0.0dB Controls the amount of dry signal to be mixed with the
distorted signal.
EQ Input Off, -49.5dB to +24dB Adjusts the input level trim to the EQs to eliminate the
possibility of clipping boosted signals.
Mid 1 Fc 10Hz to 20.0kHz Sets the center of the mid frequency parametric.
Mid 1 Q 1.0 to 40.0 This parameter is a bandwidth control that determines
the width of the resonant peak at the center frequency
band. This parameter is equal to the cutoff frequency
divided by the bandwidth. By raising the value, you can
produce a narrower bandwidth.
Mid 1 Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this mid
frequency band.
VCF Input Off, -49.5dB to 0.0dB Acts as a trim control at the input of the VCF.
VCF Fc 10Hz to 7.10kHz Determines the VCF cut off frequency. Higher values
have a brighter sound. This parameter can be modulated
by any continuous MIDI controller for a wah-wah pedal
effect.
VCF Q 1.0 to 40.0 Determines the level and width of the resonant peak at
the filter cutoff point. While the Fc (filter cutoff)
parameter determines where (at what frequency) this
peak will occur, the Q setting controls the sharpness of
the peak.
ADSR Attack 50us to 10.0s Sets the attack time for the ADSR envelope shape.
ADSR Decay 50us to 10.0s Sets the decay time for the ADSR envelope shape.
ADSR Sustain Off, -49.5dB to 0.0dB Sets the sustain level for the ADSR envelope shape.
ADSR Release 50us to 10.0s Sets the release time for the ADSR envelope shape.
ADSR Env Amt -99% to +99% Determines the degree to which the envelope modifies
the cutoff frequency of the VCF.
ADSR TrigMode Single or Multi Determines whether the envelope which controls the
VCF will retrigger with each key-event (Multi) or not
(Single).
Dly1 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the first independent
delay.
Dly1 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly1 Feedback -99% to +99% Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly1 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly1 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
Dly2 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the second
independent delay.
Dly2 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly2 Feedback -99% to +99% Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly2 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly2 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
To Next Page
Loading...
