Epson 2200 - Stylus Photo Color Inkjet Printer - Page 232

EPSON Stylus PHOTO 2100/2200 Revision B
APPENDIX Connector Summary 232
38H
39H
Replace Cleaning Counter
00H
00H
00H
00H
3AH Initial Fill Counter 00H 00H
3BH Reserved - -
3CH Fatal Error Code 00H 00H
3DH Total fever (CR) 00H 00H
3EH Total fever (PF) 00H 00H
3FH Roll paper flag
bit0: Roll paper mode
bit1: Panel load mode
00H 00H
40H
41H
Password
5AH
0FH
-
-
42H EEPROM mapping revision 41H -
43H Reserved - -
44H Interface selection
0:Auto 1:Parallel
3:USB1.1
4:1394 5:USB2.0
00H 00H
(*2)
45H Interface time-out
0 to 255
(by second,
value of 0 means 10 seconds)
0AH 0AH
46H Compatibility speed
0:Fast 1:Slow
2:Special-1 3:Special-2
00H 00H
47H ECP speed
(*a)
0:Fast 1:Slow 00H 00H
48H IEEE1284.4 for Parallel
0:Auto 1:On
2:Off
00H 01H
49H IEEE1284.4 for USB
0:Auto 1:On
2:Off
00H 01H
*a.
BUSY signal delay time from fall-edge of a -STB signal. (Fast:Max.1MB/s, Slow:Max.
600KB/s)
*b.
Select IEEE1284 transfer mode. (ECP or Nibble)
*c.
Enable or disable reverse transfer. (when disabled, ignore -SLIN signal)
Table 7-16. EEPROM Address Map
Address Explanation Setting
QPIT
setting
Factory
settings
4AH I/F Control flags
bit0: IEEE1284 mode
(0=On, 1=Off)
(*c)
bit1: ECP mode
(0=Off, 1=On)
(*b)
bit2-bit7: reserved
00H 00H
4BH
|
4FH
Reserved
-
|
-
-
|
-
50H
|
55H
CPSI password
00H
|
00H
00H
|
00H
56H Print direction control
0:Bi-D 1:Uni-D
2:Auto
02H 02H
57H CG table 08H:PC437 0AH:PC850 08H 08H
58H Font 0:Courier 00H 00H
59H Pitch 0:10cpi 00H 00H
5AH Auto LF, Network I/F mode
bit0: Auto line feed
(0=Off,1=On)
bit1: Network I/F mode
(0=Off,1=On)
bit2-bit7: reserved
00H 00H
5BH Check mod control
0:Entry Self-Test
1:Entry Hex-Dump
2:Extended settings
00H 00H
5CH PW Adjustment (HMXU)
-8 <= n <= +8
(by 0.1411mm(1/180inch))
00H (
*
1)
5DH PW Adjustment (HMYU)
-8 <= n <= +8
(by 0.1411mm(1/180inch))
00H (
*
1)
5EH PW Adjustment (HMXD)
-8 <= n <= +8
(by 0.1411mm(1/180inch))
00H (
*
1)
5FH PW Adjustment (HMYD)
-8 <= n <= +8
(by 0.1411mm(1/180inch))
00H (
*
1)
Table 7-16. EEPROM Address Map
Address Explanation Setting
QPIT
setting
Factory
settings