Epson EB-1480Fi - Connecting the Touch Unit and the Control Pad; Connection Figure

142 pages

To Next Page

To Previous Page

Introduction

Connection Figure

Connecting the Touch Unit and the Control Pad

You need the following cables when using the Touch Unit and the Control Pad.

Prepare a commercially available LAN cable and USB cable to connect the projector and the Control Pad.

(1080p60p:Max70m(CAT6a/CAT7))

(4K30p:Max40m(CAT6a/CAT7))

Main Page

About this Installation Guide2
Contents of this Guide2
- Table of Contents3
Introduction5
Using the Product Safely5
- Safety Indications5
- Explanation of Symbols5
Package Contents6
- Wall Mount6
  - Main Mount6
  - Accessories7
- Touch Unit8
  - Items to Prepare in Addition to Items Supplied with the Product9
- Touch Unit Bracket9
- Control Pad10
  - Items to Prepare in Addition to Items Supplied with the Product10
- Pen Stand10
  - Items to Prepare in Addition to Items Supplied with the Product11
Installation Work Flow12
- When Installing Multiple Projectors13
- Figures of Installation Dimensions14
- Connecting the Touch Unit and the Control Pad16
- Connection Figure16
- Connecting Multiple Projectors17
  - When Using the Interactive Function17
  - When Not Using the Interactive Function17
Installing the Wall Mount19
Cautions on Installing the Wall Mount19
Cautions on the Installation Location of23
The Wall Mount23
Wall Mount Specifications25
- External Dimensions26
- Adjustment Range28
Installation Procedure for the Wall30
- Mini PC Installation Plate30
Mount30
- Installing the Bracket32
- Adjusting the Position of the Projected Image56
- Attaching the Covers71
- Attaching a Security Cable73
Installing the Control Pad74
Notes on the Control Pad74
- For Canadian Users77
Control Pad Specifications78
- External Dimensions78
- Cable Routing Holes78
Installing the Control Pad80
Installing the Pen Stand83
Notes on the Pen Stand83
Pen Stand Specifications84
- External Dimensions84
Installing the Pen Stand85
- When Securing with Magnets85
- When Securing with Screws86
Adjusting the Interactive Pen87
Calibrating the Interactive Pen87
- Manual Calibration87
- Auto Calibration89
Installing the Touch Unit91
Notes on Handling the Touch Unit91
- For Canadian Users92
Touch Unit Installation Location93
- Notes on the Touch Unit Bracket94
Notes on the Laser95
- Attached Labels95
- Laser Diffusion Port95
Touch Unit Specifications97
- External Dimensions97
Touch Unit Bracket Specifications98
- External Dimensions98
- Adjustment Range99
Installing the Touch Unit100
- Installing the Infrared Deflectors100
- Installing the Touch Unit101
  - When Installing on the Projection Surface Without Using the Touch Unit Bracket101
  - When Using the Touch Unit Bracket to Install Outside of the Projection Surface104
- Attaching a Security Cable109
- Turning on the Touch Unit110
- Adjusting the Angle of the Laser (Touch Unit Auto Setup)111
  - When Auto Adjustment Fails117
- Calibrating the Touch Operation Position120
Setting the Projector123
Batch Setup Function123
- Setup Using a USB Flash Drive123
  - Saving Settings to the USB Flash Drive123
  - Copying Saved Settings to Other Projectors124
- Setup by Connecting the Computer and Projector with a USB Cable125
  - Saving Settings to a Computer125
  - Copying Saved Settings to Other Projectors126
- When Setup Fails128
Installing Multiple Projectors129
Projection)129
- Setting the Projector ID129
- Multi-Projection Connection Settings131
  - When Using the Interactive Functions131
  - When Not Using the Interactive Functions133
- HDMI Link Settings134
- Adjusting the Image in Multi-Projection135
- Projector Sync. Settings (Only When Using Interactive Functions)136
- EDID Settings (Only When Using Interactive Functions)137
Appendix139
List of Safety Symbols139
General Notice142

Epson EB-1480Fi - Connecting the Touch Unit and the Control Pad; Connection Figure

Table of Contents

Other manuals for Epson EB-1480Fi

Related product manuals