Epson EB-Z10005U - Switching to the Target Image

To Next Page

To Previous Page

Switching to the Target Image

You can change directly to the target image from the remote control or by

pressing the following buttons on the control panel.

The following shows the input ports for each button.

Remote control

Control panel

Input ports

Changes to images from a computer connected over the network.

For EB-Z10005U/EB-Z10000U/EB-Z9875U/EB-Z9870U only

Projecting Images

Main Page

Safety Instructions2
- Table of Contents9
Introduction13
Part Names and Functions14
- Front/Top14
- Rear15
- Base16
- Interface16
- Control Panel18
- Remote Control20
Preparing the Projector25
Installing the Projector26
- Attaching the Projector Lens Unit26
  - Attaching26
  - Removing27
- Attaching and Removing the Interface Cover28
  - Removing28
  - Attaching29
- Installation Settings30
- Screen Settings32
- Displaying a Test Pattern34
- Adjusting the Position of the Projected Image (Lens Shift)35
  - Adjusting the Tilt of the Projected Image (for Normal Installment)36
- Adjusting the Zoom37
- Adjusting the Focus37
  - When Using a Short Throw Zoom Lens ELPLU0238
- ID Settings39
Connecting Equipment41
- Connecting a Computer41
- Connecting Image Sources42
- Connecting to an External Monitor44
- Connecting a LAN Cable45
- Connecting an Hdbaset Transmitter46
- Installing the Wireless LAN Unit (ELPAP07)47
  - Using the Quick Wireless Connection USB Key48
Batch Setup49
- Setup Using a USB Flash Drive49
  - Saving Settings to the USB Flash Drive49
  - Reflecting Saved Settings to Other Projectors51
- Setup by Connecting the Computer and Projector with a USB Cable53
  - Saving Settings to a Computer53
  - Reflecting Saved Settings to Other Projectors54
- When Setup Fails56
Basic Usage57
Projecting Images58
- Automatically Detect Input Signals and Change the Projected Image (Search)58
- Switching to the Target Image59
Adjusting Projected Images60
- Correcting Distortion in the Projected Image60
- Selecting the Projection Quality (Selecting Color Mode)70
Contents71
- Setting Auto Iris71
- Changing the Aspect Ratio of the Projected Image72
  - Changing Methods72
- Adjusting the Image76
- Projecting 3D Images78
Useful Functions79
Multi-Projection Function80
- Preparation80
- Edge Blending81
- Combining Scaled Images89
Projection Functions91
- Projecting Two Images Simultaneously (Split Screen)91
  - Operating Procedures91
  - Restrictions During Split Screen Projection93
- Hiding the Image Temporarily (Shutter)94
- Freezing the Image (Freeze)95
- Enlarging Part of the Image (E-Zoom)95
- Saving a User's Logo96
Memory Function98
- Saving/Loading/Erasing the Memory98
Scheduling Function100
- Setting the Time100
- Saving a Schedule101
Security Functions107
- Managing Users (Password Protection)107
- Restricting Operation110
- Anti-Theft Lock112
  - Installing the Wire Lock112
Configuration Menu113
Using the Configuration Menu114
List of Functions115
- Configuration Menu Table115
  - Network Menu116
- Image Menu117
- Signal Menu119
- Settings Menu121
- Extended Menu122
- Network Menu127
Contents136
- Info Menu (Display Only)136
- Reset Menu138
Troubleshooting139
Using the Help140
Reading the Indicators141
Reading Status Monitor150
- Checking the Status150
  - Understanding the Screen151
  - Setting the Screen Display (LCD)152
- Explanations of the Display Content153
Problem Solving160
- Problems Relating to Images160
- Problems When Projection Starts166
  - The Projector Does Not Turn on166
- Other Problems167
Event ID170
Maintenance171
Cleaning172
- Cleaning the Projector's Surface172
- Cleaning the Lens172
- Cleaning the Air Filter172
Replacing Consumables175
- Replacing the Lamp175
- Replacing the Air Filter179
  - Air Filter Replacement Period179
  - How to Replace the Air Filter179
Image Maintenance181
- Panel Alignment181
- Color Uniformity183
Appendix185
Monitoring and Controlling186
- About Easymp Monitor186
  - About Message Broadcasting186
- Changing Settings Using a Web Browser (Web Control)186
  - Setting the Projector186
  - Displaying the Web Control Screen187
- Using the Using Mail Notification to Report Problems187
  - Reading Error Notification Emails188
- Management Using SNMP189
- Displaying the Web Remote Screen189
  - Operating the Lens190
Contents191
- ESC/VP21 Commands191
  - Command List191
  - Cable Layouts191
- About Pjlink192
- About Crestron Roomview193
  - Operating the Projector from the Computer194
Optional Accessories and Consumables198
- Optional Accessories198
- Consumables199
Screen Size and Projection Distance200
- For EB-Z10005U/EB-Z10000U/EB-Z9875U/EB-Z9870U/EB-Z9750U/EB-Z11000W/EB- Z9900W/EB-Z9800W200
- Projection Distances for EB-Z11005/EB-Z11000/EB-Z9870208
Supported Monitor Displays218
- Supported Resolutions218
Specifications220
- Projector General Specifications220
Appearance225
Glossary226
General Notes228
- About Notations228
- Trademarks and Copyrights229
Index230

Epson EB-Z10005U - Switching to the Target Image

Table of Contents

Other manuals for Epson EB-Z10005U

Related product manuals