Epson EF-100WATV Quick Setup

Quick Setup
IMPORTANT: Before using this product, make sure you read these instructions
and the safety instructions in the online User’s Guide.
Contents
Make sure your projector box includes all of these parts:
You can place the projector on almost any flat surface. See the online User’s
Guide for more information.
Connect the projector
Streaming device
Connect the included Android TV streaming device to your projector. To stream
content, make sure you have an active streaming account and enter your login
information as necessary for each app.
Note: To connect other streaming devices, see the online User’s Guide for more
information. The projector’s HDMI port does not support MHL
®
.
1
Remove the rear cover of the projector.
2
Open the USB power cable clamp.
3
Connect the streaming device to the projector’s HDMI extension cable.
4
Connect the USB power cable to the streaming device and fit the device
securely inside the projector.
Caution: Do not force the device into the projector; you may damage the
projector and/or the device.
5
Make sure the device is securely connected as shown below. Pass the USB
power cable through the clamp, then close the clamp to secure the cable.
6
Replace the rear cover of the projector.
Note: To pair a Bluetooth
®
speaker or to connect an external speaker or
headphones to your projector, see the online User’s Guide.
External video source
You can connect an external video source with an HDMI cable (not included).
Caution: Do not turn on the video source before connecting it to the projector;
you may damage the projector.
Note: Some external video sources may require an optional HDMI adapter
cable.
1
Remove the rear cover of the projector.
2
Connect an HDMI cable to your video source’s HDMI output port.
3
Connect the other end of the HDMI cable to the projector’s HDMI
extension cable.
4
Pass the HDMI cable through the cable path as shown.
5
Replace the rear cover of the projector.
Turn on the projector
1
Plug in the projector.
2
Press the power button on the projector or the projector remote
control. The power light flashes blue, then stays on.
3
Press the Enter button on the projector remote control to scroll through
the Welcome Guide. To use Android TV and video-on-demand features,
press and hold the home and Enter buttons to pair the remote control
to the projector.
4
The default language of the menu system is English. To select another
language, press the menu button on the projector remote control.
Select Settings and press Enter. Select Language and press Enter. Select
your language and press Enter. Press the menu button to exit.
Note: To shut down the projector, press the power button on the projector
or the projector remote control, then press the button again to confirm, if
necessary.
Adjust the image
1
Move the focus lever on top of the projector left or right to adjust the
image sharpness.
2
To adjust the image height, press and hold the foot release lever on the
bottom of the projector to extend the front adjustable foot. Release the
lever to lock the foot in the desired position.
Using the projector remote
control
Install the batteries as shown (two AAA batteries).
Access projector menus
Turn projector on or off
Go back to previous
function
Enter a selection
Navigate menus
Adjust image shape
(keystone)
Operate Android TV features
using voice commands
Display the Android TV
home screen
Turn off audio and
video temporarily
Microphone
Control playback of
connected device
Turn volume up or down
Connect to video-on-
demand apps
Note:
• You must pair the projector remote control to the projector to use Android TV
and video-on-demand features. See the online User’s Guide for more
information.
• The remote control for Android TV is only used to control the streaming
device if it is connected to a different device or projector. See the online
User’s Guide for more information.
Troubleshooting
•
If you see a No signal message after turning on the projector, check the
following:
•
Make sure the streaming device is properly connected to the HDMI
extension cable and the USB power cable.
•
For external video sources, make sure an HDMI cable is properly
connected to the projector’s HDMI extension cable.
•
If you see a blank screen, check the following:
•
Make sure the power light on the projector is blue and not
flashing.
•
Press the power button to wake the projector from standby or
sleep mode, if necessary.
•
If you see a blank screen when a computer is connected, check the
following:
•
On some Windows
®
laptops, you may need to hold down the Fn key
and press F7 or the function key that lets you display on an external
monitor. It may be labeled CRT/LCD or have an icon such as .
On Windows 7 or later, hold down the Windows key and press P at
the same time, then click Duplicate.
•
If you’re using a Mac laptop, open System Preferences and
select Displays. Click the Arrangement tab and select the Mirror
Displays checkbox.
•
If the projector does not respond to remote control commands, make sure
the batteries in the remote control are installed correctly. Replace the
batteries if necessary.
•
The projector’s USB power cable can provide 2.0A of power. Make sure
your streaming device supports this specification.
EF-100WATV/EF-100BATV

Epson EF-100WATV Specifications

General

Brand	Epson
Model	EF-100WATV
Category	Projector
Language	English