Quick Setup
IMPORTANT: Before using this product, make sure you read these instructions
and the safety instructions in the online User’s Guide.
Choose a location
Keep the projector level and place it at a height so its lens is even with the top
or bottom of the screen and is centered horizontally. If this isn’t possible, use the
lens shift feature to reposition the image (see “Adjust the image”).
See the online User’s Guide for more information on where to place your
projector.
Connect the projector
Connect multiple video devices and use the Source buttons on the remote
control or the Source button on the projector to switch between them. For
additional connection types, see the online User’s Guide.
HDMI cable
Power supply
USB cable
Streaming
device
Note:
• When projecting images at 4K 120Hz, use an HDMI 2.1 rated cable (ultra-high
speed).
•
You can output audio to an external sound system that supports
using the HDMI2 port.
Turn on your equipment
1
Plug in the projector.
2
Press the power button on the projector or the On button on the
remote control. The shutter opens and the power light flashes blue,
then stays on.
Note: To shut down the projector, press the power button on the
projector or the Standby button on the remote control, then press the
button again to confirm, if necessary. Wait for cooldown to complete
before unplugging the projector.
3
Follow the on-screen instructions to set up your projector. If you see a
screen displaying 123, press Enter on the remote control to continue. Use
the arrow buttons to select the correct image orientation and press Enter.
Note: To change these settings, see the online User’s Guide.
4
Turn on your video source.
5
If you don’t see an image, press one of the Source buttons on the remote
control to select the image source.
Note: If you still see a blank screen or have other display problems, see the
troubleshooting tips on this sheet.
Using the remote control
Install the batteries as shown (two AA batteries).
Choose which source to
display
Turn projector on
Access projector menus
Adjust zoom, focus,
and lens shift
Turn off projector
display
Navigate projector
menus
Turn projector off
Control connected
sources with HDMI
Link
For more information on using the remote control, see the online User’s Guide.
Adjust the image
1
Press the Pattern button on the remote control to display a test pattern.
2
Press the Lens button on the remote control and use the and buttons
to focus the image.
3
Press the Lens button on the remote control again and use the and
buttons to reduce or enlarge the image.
4
Press the Lens button on the remote control again and use the , ,
, and buttons to reposition the image.
Troubleshooting
If you see a blank screen or the No signal message after turning on your video
device or computer, check the following:
•
Make sure the power light on the projector is blue and not flashing.
•
Press the Source button on the projector or one of the Source
buttons on the remote control to switch to the correct image source, if
necessary.
•
If you’re using a Windows
®
laptop, press the function key that lets you
display on an external monitor. It may be labeled CRT/LCD or have an icon
such as . You may have to hold down the Fn key while pressing it
(such as Fn + F7). Wait a moment for the display to appear.
On Windows 7 or later, hold down the Windows key and press P at the
same time, then click Duplicate.
•
If you’re using a Mac laptop, open System Preferences and select
Displays. Click the Arrangement tab and select the Mirror Displays
checkbox.
Registration
Register today to get product updates and exclusive offers. You can register
online at http://epson.com/webreg.
Where to get help
Manual
For more information about using the projector, see the online manual. You
can view or download the online manual from the Epson website, as described
below.
Internet support
Visit http://epson.com/support/hcls11000 (U.S.) or
http://epson.ca/support/hcls11000 (Canada) for solutions to common
problems. You can download software and utilities, view manuals, get FAQs and
troubleshooting advice, or contact Epson.
Telephone support
To use the Epson PrivateLine
®
Support service, call (800) 637-7661. This service is
available for the duration of your warranty period. You may also speak with a
support specialist by calling (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).
Support hours are 6
am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change
without notice. Toll or long distance charges may apply.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase accessories from an Epson authorized reseller. To find the
nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at
http://epsonstore.com (U.S. sales) or http://epsonstore.ca (Canadian sales).
Home Cinema LS11000
To Next Page
Need help?
General