VGA cable
HDMI cable
Audio cable
USB cable
USB port
Connect the square end of a USB cable to the projector’s USB-B (square) port.
Connect the flat end of the cable to any USB port on your computer.
Windows
®
XP or later: After turning on the projector, follow the on-screen
instructions to install the Epson
®
USB Display software (EMP_UDSE.EXE; only
on first connection). If the software screen does not display automatically,
open My Computer or Computer, then double-click EPSON_PJ_UD.
Mac OS X 10.5.1 or higher: After turning on the projector, the setup folder
for USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
Computer port
Connect one end of a VGA cable to the projector’s Computer1 or
Computer2 port, and the other end to your computer’s monitor port. If
you are using a laptop, switch it to external display (see “Troubleshooting”).
You can also connect an audio cable.
HDMI port
Connect one end of an HDMI cable to the projector’s HDMI port and the other
end to an HDMI port on your computer.
Wired network
You can connect the projector to your network using an Ethernet cable.
USB cable
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s PC Free feature. See the online User’s Guide for details.
External monitor, external speakers, and microphone
You can also connect an external monitor, external speakers, or a microphone
to your projector to enhance your presentations. See the online User’s Guide
for details.
Turn on your equipment
1
Turn on your computer or video source.
2
Plug in the projector. The power light on the projector turns blue.
3
Open the A/V Mute slide all the way.
4
Press the power button on the projector or remote control. The
projector beeps, and the Status light flashes blue and then stays on.
Note: To shut down the projector, press the power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
5
The default language of the menu system is English. To select another
language, press the Menu button on the projector or remote control.
Select Extended and press . Select Language and press .
Select your language and press . Press the Menu button to exit
the menu system.
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3
Turn the zoom ring to enlarge or reduce the image.
4
Turn the focus ring to sharpen the image.
5
If your image looks like or , you may have placed the projector
off to one side of the screen at an angle. Place the projector directly in
front of the center of the screen, facing the screen squarely. If you
can’t move the projector, use the horizontal keystone slider to correct
the image.
6
Your projector automatically adjusts images that look like or ,
but if necessary you can press the or button on the projector to
correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which
source to display
Turn projector
on and off
Access projector
menus
Turn off projector
display
Get solutions to
common problems
Navigate projector
menus
For more information on using the remote control, see the online User’s
Guide.
Project wirelessly
Follow the steps here to connect the projector over a wireless network. You
will need the optional wireless LAN module (part number V12H418P12).
1
To install the wireless LAN module, first remove the screw as shown.
2
Connect the wireless LAN module to the USB-A (flat) port.
3
To configure your projector for wireless projection, do one of the
following:
•
If you’re using the optional Quick Wireless Connection USB key
(Windows only, part number V12H005M09), press the LAN button on
the remote control. When you see SSID and IP address information
on the screen, remove the wireless LAN module and connect the
key to the projector’s USB-A port. Look for the displayed message,
remove the key, and connect it to a USB port on your computer.
Follow the on-screen instructions to install the driver, then reconnect
the wireless LAN module to the projector’s USB-A port. For details,
see the online User’s Guide.
•
If you’re not using the key, continue with the steps on the next page.
PowerLite
®
97/98/99W/955W/965
To Next Page
Need help?
General
Weight and Dimensions
