Epson PP-100II - Page 48

48
*1 Specify this item when creating data discs.
*2 Specify only when creating video CDs.
*3 Specify only when burning discs using image files.
*4 In the case of ISO9660L2 format, the number of characters is limited to up to 32. Characters other than English one byte uppercase/
numerical characters and "_" cannot be used.
In the case of Joliet format, the number of characters is limited to up to 16. Characters other than English one byte uppercase/numerical
characters and "_" cannot be used.
In the case of UDF format, up to 62 characters can be used.
In the case of UDF Bridge format, the same limitation as ISO9660L2 is applied.
*5 Effective only when using BD with PP-7050BD.
*6 Disabled in PP-100N.
LABEL_TYP
E
Specify the label
type.
To specify "CD/DVD label", specify "1".
To specify “High-quality CD/DVD label”,
specify "2".
To specify "EPSON -certified CD/DVD label",
specify "3".
If not specified, the label type in the
environment settings will be used.
One character One bite
numbers
Arbitrary ● ●
PRINT_MO
DE
Specify the print
mode.
To give priority to print quality, specify "1". To
give priority to print speed, specify "2" or "3".
(Specify "3" for the fastest speed.)
If not specified, the print mode in the
environment settings will be used.
"3" can only be specified if you have the PP-
100AP.
Invalid if "EPSON-certified CD/DVD label" is
specified for the label type (the print mode is
fixed at "Quality").
One character One bite
numbers
Arbitrary ●●
IN_STACKE
R
Specify the stacker
to be used as the
input stacker.
[When the output device is External Output
Mode]
Specify "1" to set stacker 1 as the input
stacker. Specify "2" to set stacker 2 as the
input stacker. Specify "AUTO" to used
both stacker 1 and stacker 2 as the input
stackers. If not specified, the default
source in the environment settings will
be used.
[When the output device is not External
Output Mode]
Invalid (will be disregarded if specified).
Four
characters
Any of "1", "2",
"AUTO"
Arbitrary -- ●
MEASURE Specify whether to
measure the disc
recording side.
Specify "0" when not measuring.
Specify "1" when measuring the error rate.
When not specified, the disc recording side is
not measured.
(Specify "1" when the mode is set to Error Rate
Measurement Mode.)
One characters "0" or "1" Arbitrary ●
*5
--
ARCHIVE_D
ISC_ONLY
Specify whether BD
writing is limited to
archive disc.
Specify "YES" to limit.
Specify "NO" to make no limitation.
When not specified, BD writing is limited.
(Ignored when writing CD/DVD.)
Three
characters
"YES" or "NO" Arbitrary ●
*5
--
PLUG_IN_I
D
Specifies the Plug-in
to execute.
For Read Back Plug-in, specifies
"EPSONTotalDiscReader".
"EPSONTotalDiscReader" can be executed
only in PP-100II / PP-50BD / PP-7050BD.
40
characters
One-byte
numerical
characters, "_"
Arbitrary ●
*6
--
PLUG_IN_P
ARAMETER
Specifies the
parameter(s) to pass
to the Plug-in to be
executed.
See "PLUG_IN_PARAMETER" on page 4-49. 1024
characters
Characters that
contain no
control character
and can be
converted into
multi-byte
characters
Arbitrary ●
*6
--
Key
name
Explanation How to specify the setting
Maximum
characters
Available
characters
(strings)
Necessary/
Arbitrary
Except PP-
100AP, Key
available
Yes/No
PP-100AP
Key
available
Yes/No