Epson Stylus Pro 4400 - Page 491

EPSON Stylus Pro 4400/4450/4800/4880/4880C Revision C
Appendix Parts List 491
730 “LEVER,INCLINATION”
731 “EXTENSION SPRING,3.81”
732 “CARRIAGE,A;B”
734 “PLATE,BEARING,L,C593”
735 “LEVER,CAM,C593”
736 “STOPPER,CARRIAGE”
737 “SHAFT,INCLINATION CAM”
738 “HARNESS,HEAD,A”
739 “HARNESS,HEAD,C”
740 “SHEET,FFC”
741 “SOLENOID ASSY.,CR,C593,ESL,ASP”
742 “ADJUST PLATE,CR,UPPER”
743 “ADJUST PLATE,CR,LOWER”
744 “C.P.P-TITE SCREW,2.6X8,F/ZN-3C”
745 “SPACER,CARREAGE A”
746 BALL BEARING(B210151490)
747 “HARNESS,HEAD,B”
750 “EXTENSION SPRING,11.4”
751 “EXTENSION SPRING,2.55”
752 “LEVER,LOCK,PG”
753 “BUSHING,LOCK;B”
756 “EXTENSION SPRING,2.58”
757 “LEVER,SCALE,CR”
758 “EXTENSION SPRING,3.86”
759 “SCALE,CR”
760 “BELT,CR”
761 “PULLEY,DRIVEN”
762 “SHAFT,PULLEY”
763 “COMPRESSION SPRING,29.4”
770 “DETECTOR,HP;E”
772 “BELT,PG”
773 “HARNESS,DETECTOR,PG”
774 “DETECTOR,HP;E”
778 “BOARD ASSY.,ENCODER”
779 “HOLDER,TUBE,B,C593”
Table 7-10. Stylus Pro 4800
Figure Part Name
780 “PAD,TUBE”
781 “HOLDER,TUBE,A,C593”
782 “BOARD ASSY.,SUB”
783 “HARNESS,ENCODER”
784 “COVER,TUBE,C593”
785 “GUIDE,TUBE,CR,C593”
786 “SHEET,TUBE”
787 “GUIDE PLATE,TUBE”
788 “SHEET,SUS”
789 “HOLDER,FFC,C593”
790-A “SPACER,MIDDLE,0.05”
790-B “SPACER,MIDDLE,0.1”
790-C “SPACER,MIDDLE,0.2”
790-D “SPACER,MIDDLE,0.5”
790-E “SPACER,MIDDLE,0.08”
791 “HARNESS,DETECTOR,HP”
792 BALL BEARING(B210151490)
800 “DETECTOR,LEAF,B2”
801 “HARNESS,PAPER EJECT PHASE,LEFT”
802 “LEVER,CHANGE PAPER EJECT,L”
803 “EXTENSION SPRING,6.99”
805 “MOUNT PLATE,MOTOR,ASF ASSY.,C593”
806 “COMBINATION GEAR,12,22.4”
807 “SPUR GEAR,25.6”
808 “COMBINATION GEAR,12.8,36”
809 “COMBINATION GEAR,13.6,28.8”
810 “SPUR GEAR,20”
811A “PG TRANSMIT ASSY.,C593”
814 “HOLDER,PLANET,RELEASE;B”
815 “SPUR GEAR,16,RELEASE”
816 “SPUR GEAR,22,RELEASE”
817 “POLY SLIDER,STW-FT70,t=0.25”
818 “COMPRESSION SPRING,0.98”
819 “SHEET,FRAME,RIGHT”
820 “EXTENSION SPRING,2.41”
Table 7-10. Stylus Pro 4800
Figure Part Name