What to do if my Eurostar EURO-9700 GOLD has no sound?
If your Eurostar Receiver has no sound, ensure the RCA cable is correctly connected. Also, verify that the volume isn't set too low and that the mute function isn't activated. Correct the connection, increase the volume on both the TV and receiver, and press the MUTE key.
What to do if my Eurostar EURO-9700 GOLD Receiver shows no video/picture on the TV screen?
If there is no video or picture on your TV screen when using your Eurostar Receiver, first ensure the receiver is powered on and not in standby mode. Check the RCA cable connection to ensure it's properly connected. Finally, verify that you've selected the correct channel and video input on your television and adjust accordingly.
Why is my Eurostar EURO-9700 GOLD Receiver remote control not functioning?
If the remote control for your Eurostar Receiver isn't working, make sure you are pointing it directly at the receiver. Also, check the batteries to ensure they aren't discharged or inserted incorrectly. Replace the batteries or correctly insert them.
What to do if my Eurostar EURO-9700 GOLD shows the error message “Searching for signal”?
If your Eurostar Receiver displays the error message “Searching for signal”, check that the antenna cable is securely connected. It could also indicate a defective LNB or incorrect alignment of the satellite antenna. Verify that the “LNB POWER” is not set to “Off” in the LNB setting menu. Check the cable and tighten its connection, change the LNB, align the satellite antenna properly, and check the signal strength in the “Auto Scan” menu.
Why does my Eurostar Receiver have poor or freezing picture quality?
If you are experiencing poor or freezing picture quality on your Eurostar Receiver, it's likely due to a low signal strength. Check the signal strength in the “Auto Scan” menu and align the dish properly.
How to fix the “No programs are stored” error on my Eurostar EURO-9700 GOLD Receiver?
General| FTA (Free to Air) | Yes |
|---|---|
| HDTV Compatible | Yes |
| EPG (Electronic Program Guide) | Yes |
| Tuner Type | DVB-S2 |
| Supported Video Formats | MPEG-2, MPEG-4, H.264 |
| HDMI Output | Yes |
| Resolution | Up to 1080p |
| Connectivity | 1x HDMI, 1x USB |
| DiSEqC | 1.0, 1.1, 1.2 |
| USB Port | Yes |
Device is for receiving satellite programs only; other uses are not allowed.
Read and follow safety precautions for device operation, maintenance, and care.
Proper ventilation and placement guidelines for the satellite receiver.
Connect coaxial cable from LNB to DISH INPUT terminal using finger-tightened connectors.
Connect receiver to TV via RF or RCA cable for audio and video output.
Connect external audio systems using RCA connectors for Left and Right Audio.
Description of the front panel controls and display functions.
Details of the input/output terminals on the rear panel of the receiver.
Explains the information banner and how to navigate it.
Instructions for adjusting volume, muting, and selecting audio channels.
How to view and navigate the service list using remote control keys.
How to select and view channels filtered by service provider.
How to select and view channels filtered by transponder.
How to view weekly and detailed program guides using EPG.
How to select and change subtitle language for broadcasts.
Configure OSD, audio, teletext, subtitle, and EPG languages.
Accessing and navigating the main menu and its sub-menus.
Set satellite, LNB power, offset, and 22 KHz tone for signal reception.
Select between User and Installer modes for DiSEqC control.
Detailed operations for installers, including drive motor control and limit settings.
Tune-in new channels manually by inputting frequency, symbol rate, and FEC.
Run diagnostic tests to check the condition of receiver components.
Download and upgrade receiver software via satellite.
Recover factory settings to resolve issues or reset the receiver.
Create and manage favorite channel lists by categorizing content.
Options to Delete, Skip, Move, or Rename channels.
Rearrange the order of channels within the channel list.
Edit channel names using the on-screen keyboard and font tables.
Select OSD, audio, teletext, subtitle, and EPG languages.
Configure TV system (PAL/NTSC) and aspect ratio (4:3/16:9).
Adjust OSD transparency, banner timeout, and other display options.
Lock individual channels or content items requiring a PIN code.
Procedure to change the existing PIN code for parental control.
Common problems and their solutions for receiver operation.
Detailed technical data for video, audio, demodulator, and output sections.
To Next Page