1: ADD/REMOVE
--Manual add mode: Press the button 3 times
--Auto-add mode: LED will blink within 30 seconds aer power on
press 1x: On/Off the Le outlet
press 2x: On/Off the Right outlet
hold 3s: On/Off simultaneously.
2: Factory reset:
Manual : Click the button 2 times quickly, and hold for at least
10 seconds
Host reset: Remove it from the host and the device is factory reset.
3: Association
Support 3 groups, each group max support 2 devices
(LED flashes 2 times when the configuration parameter changed.)
Group 1 lifeline
Group 2 le outlet send basic set
Group 3 right outlet send basic set
4: LED Indicator
(LED flashes 2 times when the configuration parameter changed.)
quickly press 6x: change parameter
--Parameter =1, size =1 byte, value=00(default)output on, LED on
--Parameter =1, size =1 byte, value=01 output on, LED off
--Parameter =1, size =1 byte, value=02 LED no work
5:
Auto Turn-Off Timer
(LED flashes 2 times when the configuration parameter changed.)
--Parameter =2, size=4 byte, value= 1 – 65535 (Min), le outlet off
--Parameter =3, size=4 byte, value= 1 – 65535 (Min), right outlet off
6:
Auto Turn-On Timer
(LED flashes 2 times when the configuration parameter changed.)
--Parameter =4, size=4 byte, value= 1 – 65535 (Min), le outlet on
--Parameter =5, size=4 byte, value= 1 – 65535 (Min), right outlet on
7：Restores state aer power failure(quickly press 10x: change Parameter)
(LED flashes 2 times when the configuration parameter changed.)
Parameter=6，Size=1，Value=0 output off
Value=1 output on
Value=2 out put the state aer power(default)
Parameter Settings
Outdoor Smart Plug
( 2 channel )
Specifications
+
Meet your new smart plug !
(A) Manual / Program button
Those are your smart outlets that will be
included to your smart Hub/Gateway.
(B/C) Smart Outlet
press 1x: On/Off the Le outlet
press 2x: On/Off the Right outlet
hold 3s: On/Off simultaneously.
Put the Z-wave interface controller into “Add” mode, triple press
the Program button (A). It will be included to network. (Once your
controller confirmed, refresh the Z-Wave network to optimize
performance. )
Put the Z-Wave interface controller into "Remove" mode, triple
press the Program button (A). It will be excluded to network.
Manual reset: Click the button 2 times quickly, and hold for at least
10 seconds.
Host reset: Remove it from the host and the device is factory reset.
Note: This should only be used in the event your network’s primary
controller is missing or otherwise inoperable.
Add to Z-Wave Network
Remove from Z-Wave Network
To return your switch to factory defaults
Note:
Include the device to the network
within 10 feet of the controller when
adding to the controller then
relocate it to the desired position in
your home, no more than 100 feet
distance from controller. Be sure to
refresh the network while the device
is included in this manner.
One Z-Wave controlled AC outlet for standard incandescent
lighting, CFL/LED. Total load capacity for both outlets is
15A(1800W) Resistive.
Plug the device you want to control into the Z-Wave Smart plug
controlled outlet .
NOTE: Plug directly into outlet, do not use with extension cords.
Model: ZW97
Power: 120VAC, 60Hz
Loading : 15 Amp Smart Outlet*2
Total(Both Outlets): 15 Amp Max
Frequency: 908.42 MHz
Operating Temperature: -4° F~122° F
A
B
C
100 feet
Introduction
The EVA LOGIK ZW97 is a Z-Wave enabled 15A receptacle designed for
using of most residential lighting and motor applications. It's compatible
with LED, halogen, incandescent, xenon, fluorescent and compact
fluorescent bulbs.The ZW97 fully works with the Fibaro, Smartthings,
Wink hub as well as all other certified Z-Wave controllers.
The Internet of Things offers tremendous promise to consumers by
enabling remote control and management of an ever-growing variety
of connected devices—from home security systems to energy manage-
ment, appliances and lighting, and remote home monitoring, just to
name a few categories.
Analysts predict that billions of devices will be connected to the
Internet of Things in the coming years. One key consideration is how
all of these devices will be integrated and controlled, and common
standards are key to enabling simple, straight forward installation and
management of devices in the connected home.
The Z-Wave protocol is an interoperable, wireless, RF-based communi-
cations technology designed specifically for control, monitoring and
status reading applications in residential and light commercial
environments. Mature, proven and broadly deployed (with over 100
million products sold worldwide), Z-Wave is by far the world market
leader in wireless control, bringing affordable, reliable and
easy-to-use ‘smart’ products to many millions of people in every
aspect of daily life.
Z-Wave Internet
• ZW97 •
• White LED indicator
For outdoor use
IP65 rated
Plug * 1
Screw * 1
Plastic Anchor * 1
Manual * 1
To Next Page
Need help?
General
