IP Unicast Commands
ExtremeWare XOS 11.5 supports only the Summit X450 family of switches and the BlackDiamond 8800 series switch.
ExtremeWare XOS 11.5 Command Reference Guide
1400
Example
The following command displays the IP ARP table for the current virtual router:
show iparp
The following is sample output for the command:
VR Destination Mac Age Static VLAN VID Port
VR-Default 10.10.10.6 00:04:96:1f:a5:71 8 NO bluered 4092 1
VR-Default 10.128.32.1 00:01:30:ba:6a:a0 0 NO Default 4095
VR-Default 10.128.32.2 00:01:03:1c:ae:b0 5 NO Default 4095
VR-Default 10.128.32.4 00:d0:59:17:74:83 3 NO Default 4095
VR-Default 10.128.32.5 00:02:a5:c2:5c:dd 0 NO Default 4095
VR-Default 10.128.32.6 00:12:3f:1c:f8:fb 5 NO Default 4095
VR-Default 10.128.32.7 00:11:11:80:9c:b9 7 NO Default 4095
VR-Default 10.128.32.8 00:11:43:53:8e:f1 0 NO Default 4095
VR-Default 10.128.32.9 00:02:a5:bf:ac:70 7 NO Default 4095
VR-Default 10.128.32.10 00:11:43:44:18:68 10 NO Default 4095
VR-Default 10.128.32.11 00:12:3f:1c:e9:f2 0 NO Default 4095
VR-Default 10.128.32.12 00:02:a5:bf:af:79 8 NO Default 4095
VR-Default 10.128.32.13 00:11:43:40:89:91 0 NO Default 4095
VR-Default 10.128.32.16 00:0f:1f:c9:2d:80 2 NO Default 4095
VR-Default 10.128.32.17 00:06:5b:b1:6a:91 1 NO Default 4095
VR-Default 10.128.32.19 00:11:43:3a:96:1d 10 NO Default 4095
VR-Default 10.128.32.20 00:08:02:d5:c5:b7 6 NO Default 4095
VR-Default 10.128.32.24 00:12:3f:0a:44:92 14 NO Default 4095
VR-Default 10.128.32.26 00:50:04:ad:36:5e 6 NO Default 4095
VR-Default 10.128.32.30 00:b0:d0:23:f2:9a 11 NO Default 4095
VR-Default 10.128.32.54 00:b0:d0:59:e4:e2 6 NO Default 4095
VR-Default 10.128.32.55 00:a0:c9:0c:41:de 3 NO Default 4095
VR-Default 10.128.32.59 00:b0:d0:7c:d6:07 14 NO Default 4095
VR-Default 10.128.32.99 00:04:96:05:00:03 13 NO Default 4095
VR-Default 10.128.32.101 00:04:96:1f:a8:48 0 NO Default 4095
RX Error The number of incorrect ARP request and reply packets received. The
malformed packets include the following errors: incorrect ARP op code,
hardware address type is not ethernet, the protocol address is not IP, and
similar errors.
Dup IP Addr IP addresses that have been used by other hosts on the network.
Rejected Count The number of rejected ARP request packets.
Rejected IP The source address for the last rejected ARP request. An example reason for
an ARP request packet to be rejected is if the source address of the packet is
not in the subnet.
Rejected Port The port on which the last rejected ARP request packet arrived.
Rejected I/F The VLAN on which the last rejected ARP request packet arrived.
Max ARP entries Maximum ARP table size for the virtual router (each virtual router has its own
ARP table).
Max ARP pending entries Maximum number of incomplete (pending) ARP entries allowed in the table.
ARP address check Whether IP ARP checking is enabled or disabled. IP ARP checking verifies if
the ARP request’s source address is in the receiving interface’s subnet.
ARP refresh Whether ARP refresh is enabled or disabled. ARP refresh is performed when an
ARP entry’s age is three-fourths of the timeout value.
Timeout Timeout value for a dynamic (learned) ARP entry.
To Next Page
Loading...