FAAC A1400 AIR RDT

To Previous Page

FAAC S.p.A. Soc. Unipersonale

Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY

Tel. +39 051 61724 - Fax +39 051 758518

www.faac.it - www.faacgroup.com

A1400 AIR RDT 118 532119 04 - Rev. C

Main Page

Default Chapter4
- EC Declaration of Conformity of a Machine4
- EC Declaration of Conformity4
- Declaration of Incorporation of Partly Completed Machinery5
- Table of Contents6
1 Introduction to the Instructions Manual9
- Safety Recommendations9
- Meaning of the Symbols Used10
- Symbols: Notes and Warnings on the Instructions10
- Symbols: Work Equipment (Type and Size)10
- Symbols: Safety Recommendations (en ISO 7010)11
- Symbols: Signs on the Product11
- Symbols: Personal Protective Equipment11
- Symbols: Signs on the Packaging11
2 Automation A1400 Air Rdt12
- Intended Use12
  - Limitations for Use12
- Unauthorised Use12
- Identification Plate13
- Technical Specifications14
- Composition of the Supply15
  - Installation Stages According to Type of Supply15
  - Components of the Automation16
3 Required Inspections and Arrangements18
- Preliminary Inspections18
- Arrangement of Electrical Cables18
4 Transport and Reception of the Consignment19
- Handle Packages19
- Unpack and Handle19
5 Cut the Profiles20
- Profile Cutting Measurements20
6 Assemble the Head Section21
- Preliminary for Self-Supporting Head Section (if Any)21
- Assemble the Components22
7 Assemble the Frame A1400 Air Rdt Cs26
- Entry Door with Profiles TK5026
- Entry Door with Profiles TK2027
8 Install the Head Section29
- Preliminary Operations29
- Wall Fastening29
- Self-Supporting Automation Fastening30
  - Mount the Transom31
9 Install Leaves32
- Mount the Lower Shoes32
- Mount Profiles on the Leaves33
- Mount the Lower Brush Strip33
  - Glass Leaves33
- Install Leaves33
- Preparing the External Carriages34
- Telescopic Profile Assembly35
- Plate on Telescopic Profile36
- Preparing External Carriages36
- Steel Cable Fixing38
- Adjust Leaves and Carriages39
10 Install Glass Leaves40
- Mount the Sweepers42
11 Assemble the Belt, Casing and Accessories43
- Mount the Belt43
  - Adjust the Belt44
- Belt Tensioning45
- Belt Tensioning (Measurements in45
12 Electronic Installation51
- Electronics Module51
  - Electronic Board E1400 RD51
- LED on the Board52
13 Commissioning63
- Preliminary Checks Prior to Commissioning63
- System Power Supply and SETUP63
  - Checks Following SETUP63
  - Saving the Configuration63
- Basic / Advanced Programming64
14 System Functionality/Configurations68
- Operating Mode68
- Inputs Configuration69
- Configuration of J22 Outputs71
- Obstacle Detection71
- Anti-Intrusion and PULL&GO71
- Function Energy Saving72
  - How to Activate Theenergy Saving72
- Function Low Energy in Closing72
- Cs Cf72
  - How to Set Low Energy on Closure72
- 3 Setting Max Speed in Low Energy72
15 Diagnostics and Procedures73
- Acoustic Signal73
- System Diagnostics: Alerts, Errors73
- 4 Statuses of the Automation73
  - Solution of Problems or Outages76
16 Operations on the Board77
- Setup77
  - How to Perform Setup from Board77
- Reset77
  - When Is Reset Necessary77
  - How to Perform RESET from Board77
- Restoring Factory Status77
  - When Is Restore Necessary77
  - How to Perform Restore77
- Update (UPLOAD)78
- Download78
- 2 BOOTLOADER Errors79
17 Lkevo80
- Selection MENU80
- Firmware Version81
18 Sdk Evo84
- Assembly and Testing84
- Switching on and Use84
- Home Page85
- Reset - Block/Release SDKEVO85
- Password85
- Selection MENU86
- Function MENU87
- Errors88
- AUX Errors88
19 Maintenance97
- Calculation Estimate of Cycles Performed97
  - Routine Maintenance97
  - Periodic Replacements97
- Maintenance Technician Safety98
- Replacements98
- Cleaning100
- Functional Checks100
20 Waste Disposal100
21 Annexes101
- Positions of Components on the Head Section101

FAAC A1400 AIR RDT - Page 118

Table of Contents

Related product manuals