Fagor 8035-T - Page 432

 Installation manual
CNC 8035
C.
APPENDIX
Summary of internal CNC variables.
(SOFT M: V15.3X)
(S
OFT T: V16.3X)
·432·
Variables associated with work zones.
Feedrate related variables.
Variables associated with function G94.
Variables associated with function G95.
Variables associated with function G32.
Variables associated with feedrate override (%)
Coordinate related variables.
Variable CNC PLC DNC
( section 11.4 )
FZONE R R/W R Status of work zone 1.
FZLO(X-C) R R/W R Work zone 1. Lower limit along the selected axis (X/C).
FZUP(X-C) R R/W R Work zone 1. Upper limit along the selected axis (X-C).
SZONE R R/W R Status of work zone 2.
SZLO(X-C) R R/W R Work zone 2. Lower limit along the selected axis (X/C).
SZUP(X-C) R R/W R Work zone 2. Upper limit along the selected axis (X-C).
TZONE R R/W R Status of work zone 3.
TZLO(X-C) R R/W R Work zone 3. Lower limit along the selected axis (X/C).
TZUP(X-C) R R/W R Work zone 3. Upper limit along the selected axis (X-C).
FOZONE R R/W R Status of work zone 4.
FOZLO(X-C) R R/W R Work zone 4. Lower limit along the selected axis (X/C).
FOZUP(X-C) R R/W R Work zone 4. Upper limit along the selected axis (X-C).
FIZONE R R/W R Status of work zone 5.
FIZLO(X-C) R R/W R Work zone 5. Lower limit along the selected axis (X/C).
FIZUP(X-C) R R/W R Work zone 5. Upper limit along the selected axis (X-C).
Variable CNC PLC DNC
( section 11.5 )
FREAL R R R Real feedrate of the CNC in mm/min or inch/min.
FREAL(X-C) R R R Actual (real) CNC feedrate of the selected axis.
FTEO/X-C) R R R Theoretical CNC feedrate of the selected axis.
FEED R R R Active feedrate at the CNC in mm/min or inch/min.
DNCF R R R/W Feedrate selected via DNC.
PLCF R R/W R Feedrate selected via PLC.
PRGF R R R Feedrate selected by program.
FPREV R R R Active feedrate at CNC, in m/rev or inch/rev.
DNCFPR R R R/W Feedrate selected via DNC.
PLCFPR R R/W R Feedrate selected via PLC.
PRGFPR R R R Feedrate selected by program.
PRGFIN R R R Feedrate selected by program, in 1/min.
FRO R R R Feedrate Override (%) active at the CNC.
PRGFRO R/W R R Override (%) selected by program.
DNCFRO R R R/W Override (%) selected via DNC.
PLCFRO R R/W R Override (%) selected via PLC.
CNCFRO R R R Override (%) selected from the front panel knob.
PLCCFR R R/W R Override (%) of the PLC execution channel.
Variable CNC PLC DNC
( section 11.6 )
PPOS(X-C) R - - Programmed theoretical position value (coordinate).
POS(X-C) R R R Machine coordinates. Real coordinates of the tool base.
TPOS(X-C) R R R Machine coordinates. Theoretical coordinates of the tool base.
APOS(X-C) R R R Part coordinates. Real coordinates of the tool base.
ATPOS(X-C) R R R Part coordinates. Theoretical coordinates of the tool base.
DPOS(X-C) R R R Theoretical position of the probe when the probe touched the part.
FLWE(X-C) R R R Following error of the indicated axis.
DIST(X-C) R/W R/W R Distance traveled by the indicated axis.
LIMPL(X-C) R/W R/W R Second upper travel limit.
LIMMI(X-C) R/W R/W R Second lower travel limit.
DPLY(X-C) R R R Coordinate of the selected axis displayed on the screen.
GPOS(X-C)n p R - - Coordinate of the selected axis, programmed in the (n) block of the program
(p).