Fagor CNC 8070 - Related to General Machine Parameters



 Programming manual
402
CNC 8070
14.
CNC VARIABLES
Related to general machine parameters
(SOFT V02.0X)
364
14.2 Related to general machine parameters
These variables are read-only (R) synchronous and are evaluated execution time.
They have generic names.
• Replace the "x" letter with the axis number.
• Replace the letters "i" and "m" with numbers keeping the brackets.
The PLC reading of TORQDIST, PRELOAD, TPROGAIN and TCOMPLIM comes in hundredths
(x100). Ver "Access to numeric values from the PLC" en la página 358.
(V.)MPG.AXISNAMEx V.MPG.AXISNAME2 V.MPG.AXISNAME3
(V.)MPG.MASTERAXIS[i] V.MPG.MASTERAXIS[1] V.MPG.MASTERAXIS[2]
CHANNEL CONFIGURATION PRG PLC INT
(V.)MPG.NCHANNEL
Number of CNC channels. R R R
AXIS CONFIGURATION
PRG PLC INT
(V.)MPG.NAXIS
Number of axes governed by the CNC R R R
(V.)MPG.AXISNAMEx
Name of the "n" logic axis — — R
(V.)MPG.TMASTERAXIS[i]
Tandem [i]. Logic number of the master axis R R R
(V.)MPG.TSLAVEAXIS[i]
Tandem [i]. Logic number of the slave axis R R R
(V.)MPG.TORQDIST[i]
Tandem [i]. Torque distribution R R R
(V.)MPG.PRELOAD[i]
Tandem [i]. Preload R R R
(V.)MPG.PRELFITI[i]
Tandem [i]. Time to apply the preload R R R
(V.)MPG.TPROGAIN[i]
Tandem [i]. Proportional gain R R R
(V.)MPG.TINTIME[i]
Tandem [i]. Integral gain R R R
(V.)MPG.TCOMPLIM[i]
Tandem [i]. Compensation Limit R R R
(V.)MPG.MASTERAXIS[i]
Gantry [i]. Logic number of the master axis R R R
(V.)MPG.SLAVEAXIS[i]
Gantry [i]. Logic number of the slave axis R R R
(V.)MPG.WARNCOUPE[i]
Gantry [i]. Maximum difference to issue a warning R R R
(V.)MPG.MAXCOUPE[i]
Gantry [i]. Maximum difference allowed R R R
(V.)MPG.DIFFCOMP[i]
Gantry [i]. Error difference compensation.
"0" = No "1"= Yes
RRR
SPINDLE CONFIGURATION
PRG PLC INT
(V.)MPG.NSPDL
Number of spindles governed by the CNC R R R
(V.)MPG.SPDLNAMEx
Name of the "x" spindle — — R
TIME SETTING
PRG PLC INT
(V.)MPG.LOOPTIME
Loop time R R R
(V.)MPG.PRGFREQ
Frequency of the PRG module (in cycles) R R R
CAN AND SERCOS BUS CONFIGURATION
PRG PLC INT
(V.)MPG.SERBRATE
Sercos transmission speed
"0" = 4Mbps "1" = 2Mbps
RRR
(V.)MPG.SERPOWSE
Sercos optical power R R R
(V.)MPG.CANLENGTH
Can bus cable length (in meters)
"0" = Up to 20 "1" = Up to 30 "2" = Up to 40
"3" = Up to 50 "4" = Up to 60 "5" = Up to 70
"6" = Up to 80 "7" = Up to 90 "8" = Up to 100
"9" >100
RRR
DEFAULT CONDITIONS
PRG PLC INT
(V.)MPG.INCHES
Default work units
"0" = mm "1" = inch
RRR