Fagor CNC 8070 - Sercos diagnosis



 Programming manual
CNC 8070
CNC VARIABLES
Related to axis machine parameters
14.
(SOFT V02.0X)
369
PLC reading of LOSPDLIM, UPSPDLIM, STEPOVR, MINOVR and MAXOVR comes in tenths (a
reading of 10 for 1%) Ver "Access to numeric values from the PLC" en la página 358.
SPINDLE
Lin Rot Spd Ana Ser
(V.)[n].MPA.AUTOGEAR.Xn
Automatic gear change
"0" = No "1"= Yes
— — Yes Yes P/S
(V.)[n].MPA.LOSPDLIM.Xn
Lower "rpm OK" percentage — — Yes Yes P/S
(V.)[n].MPA.UPSPDLIM.Xn
Upper "rpm OK" percentage — — Yes Yes P/S
(V.)[n].MPA.SPDLTIME.Xn
Estimated time for an S function — — Yes Yes P/S
(V.)[n].MPA.SPDLSTOP.Xn
M2, M30 and Reset stop the spindle
"0" = No "1"= Yes
— — Yes Yes P/S
(V.)[n].MPA.SREVM05.Xn
G84. Reversal stops the spindle
"0" = No "1"= Yes
— — Yes Yes P/S
(V.)[n].MPA.STEPOVR.Xn
Override step — — Yes Yes P/S
(V.)[n].MPA.MINOVR.Xn
Minimum override (%) — — Yes Yes P/S
(V.)[n].MPA.MAXOVR.Xn
Maximum override (%) — — Yes Yes P/S
SOFTWARE AXIS LIMITS
Lin Rot Spd Ana Ser
(V.)[n].MPA.POSLIMIT.Xn
Positive software limit Yes Yes — Yes P/S
(V.)[n].MPA.NEGLIMIT.Xn
Negative software limit Yes Yes — Yes P/S
(V.)[n].MPA.SWLIMITTOL.Xn
Software limit tolerance Yes Yes — Yes P/S
RUNAWAY PROTECTION
Lin Rot Spd Ana Ser
(V.)[n].MPA.TENDENCY.Xn
Activation of tendency test
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
PLC OFFSET
Lin Rot Spd Ana Ser
(V.)[n].MPA.PLCOINC.Xn
PLC offset increment per cycle Yes Yes Yes Yes P/S
DWELL FOR DEAD AXES
Lin Rot Spd Ana Ser
(V.)[n].MPA.DWELL.Xn
Dwell for dead axes Yes Yes Yes Yes P/S
RADIUS / DIAMETER
Lin Rot Spd Ana Ser
(V.)[n].MPA.DIAMPROG.Xn
Programming in diameters
"0" = No "1"= Yes
Yes — — Yes P/S
HOME SEARCH
Lin Rot Spd Ana Ser
(V.)[n].MPA.REFDIREC.Xn
Home search direction
"0" = Negative "1" = Positive
Yes Yes Yes Yes P/S
(V.)[n].MPA.DECINPUT.Xn
Home switch
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
PROBE
Lin Rot Spd Ana Ser
(V.)[n].MPA.PROBEAXIS.Xn
Probing axis Yes Yes — Yes P/S
(V.)[n].MPA.PROBERANGE.Xn
Maximum braking distance Yes Yes — Yes P/S
(V.)[n].MPA.PROBEFEED.Xn
Probing feedrate Yes Yes — Yes P/S
(V.)[n].MPA.PROBEDELAY
Delay for the "probe 1" signal Yes Yes — Yes P/S
(V.)[n].MPA.PROBEDELAY
Delay for the "probe 2" signal Yes Yes — Yes P/S
TOOL INSPECTION
Lin Rot Spd Ana Ser
(V.)[n].MPA.REPOSFEED.Xn
Maximum repositioning feedrate Yes Yes — Yes P/S
INDEPENDENT AXIS
Lin Rot Spd Ana Ser
(V.)[n].MPA.POSFEED.Xn
Positioning feedrate Yes Yes Yes Yes P/S
(V.)[n].MPA.DSYNCVELW.Xn
Velocity synchronization window Yes Yes Yes Yes P/S
(V.)[n].MPA.DSYNCPOSW.Xn
Position synchronization window Yes Yes Yes Yes P/S