Fagor CNC 8070 - Save the CAN configuration for the start-up test.



 Programming manual
402
CNC 8070
14.
CNC VARIABLES
Related to axis machine parameters
(SOFT V02.0X)
370
JOG MODE
Lin
Rot
Spd Ana Ser
(V.)[n].MPA.MANPOSSW.Xn
Maximum positive travel with G201 Yes — Yes P/S
(V.)[n].MPA.MANNEGSW.Xn
Maximum negative travel with G201 Yes — Yes P/S
(V.)[n].MPA.JOGFEED.Xn
Continuous JOG mode feedrate Yes — Yes P/S
(V.)[n].MPA.JOGRAPFEED.Xn
Rapid feed in continuous JOG mode Yes — Yes P/S
(V.)[n].MPA.MAXMANFEED.Xn
Maximum feed in continuous JOG Yes — Yes P/S
(V.)[n].MPA.MAXMANACC.Xn
Maximum acceleration in JOG mode Yes — Yes P/S
(V.)[n].MPA.MANFEEDP.Xn
Maximum % of jog feedrate with G201 Yes — Yes P/S
(V.)[n].MPA.IPOFEEDP.Xn
Maximum % of execution feedrate with G201 Yes — Yes P/S
(V.)[n].MPA.MANACCP.Xn
Maximum % of jog acceleration with G201 Yes — Yes P/S
(V.)[n].MPA.IPOACCP.Xn
Maximum % of execution acceleration with G201 Yes — Yes P/S
JOG MODE. HANDWHEELS Lin Rot Spd Ana Ser
(V.)[n].MPA.MPGRESOL[i].Xn
Dial resolution at the [i] position Yes Yes — Yes P/S
(V.)[n].MPA.MPGFILTER.Xn
Filter time for the handwheel Yes Yes — Yes P/S
JOG MODE. INCREMENTAL JOG Lin Rot Spd Ana Ser
(V.)[n].MPA.INCJOGDIST[i].Xn
Moving distance at [i] dial position Yes Yes — Yes P/S
(V.)[n].MPA.INCJOGFEED[i].Xn
Feedrate at [i] position Yes Yes — Yes P/S
LEADSCREW ERROR COMPENSATION Lin Rot Spd Ana Ser
(V.)[n].MPA.LSCRWCOMP.Xn
Leadscrew error compensation
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
(V.)[n].MPA.NPOINTS.Xn
Number of points in the table Yes Yes Yes Yes P/S
(V.)[n].MPA.TYPLSCRW.Xn
Type of compensation
"0" = Real coordinates "1" = Theoretical
coordinates
Yes Yes Yes Yes P/S
(V.)[n].MPA.BIDIR.Xn
Bi-directional compensation
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
(V.)[n].MPA.REFNEED.Xn
Mandatory home search
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
(V.)[n].MPA.POSITION[i].Xn
Master axis position for point [i] Yes Yes Yes Yes P/S
(V.)[n].MPA.POSERROR[i].Xn
Error of point [i] in the positive direction Yes Yes Yes Yes P/S
(V.)[n].MPA.NEGERROR[i].Xn
Error of point [i] in the negative direction Yes Yes Yes Yes P/S
FILTERS
Lin Rot Spd Ana Ser
(V.)[n].MPA.ORDER[i].Xn
Filter order Yes Yes Yes Yes P/S
(V.)[n].MPA.TYPE[i].Xn
Type of filter
"1" = Low passing "2" = Anti-resonance
Yes Yes Yes Yes P/S
(V.)[n].MPA.FREQUENCY[i].Xn
Break or center frequency Yes Yes Yes Yes P/S
(V.)[n].MPA.NORBWIDTH[i].Xn
Normal bandwidth Yes Yes Yes Yes P/S
(V.)[n].MPA.SHARE[i].Xn
% of signal going through the filter Yes Yes Yes Yes P/S
WORK SETS
Lin Rot Spd Ana Ser
(V.)[n].MPA.NPARSETS.Xn
Number of work sets Yes Yes Yes Yes P/S
(V.)[n].MPA.DEFAULTSET.Xn
Default work set (on power-up) Yes Yes Yes Yes P/S