Fagor CNC 8070 - Report generation



 Programming manual
CNC 8070
CNC VARIABLES
Related to axis machine parameters
14.
(SOFT V02.0X)
371
14.3.1 Related to gear parameters
These variables may be accessed from the program (PRG), PLC and interface (INT), they are
read-only (R) synchronous and are evaluated in execution time.
They have generic names.
• Replace the "n" character with the channel number, maintaining the brackets. The first
channel is identified with the number 1, "0" is not a valid number.
• Replace the letter "g" with a gear number keeping the brackets. The first gear is identified
with the number 1, "0" is not a valid number.
• Replace the "Xn" character by the name, logic number or index in the channel of the axis or
of the spindle.
(V.)[n].MPA.COUNTERID[g].Xn V.[1].MPA.COUNTERID[1].X V.[2].MPA.COUNTERID[2].1
(V.)[n].MPA.PITCH[g].Xn V.[2].MPA.PITCH[1].Z V.[4].MPA.PITCH[2].3
RESOLUTION
Lin
Rot
Spd Ana Ser
(V.)[n].MPA.PITCH[g].Xn
Leadscrew pitch Yes Yes Yes P/S
(V.)[n].MPA.PITCH2[g].Xn
Leadscrew pitch (2nd feedback) Yes Yes — P/S
(V.)[n].MPA.NPULSES[g].Xn
Number of encoder pulses Yes Yes Yes S
(V.)[n].MPA.NPULSES2[g].Xn
Number of encoder pulses (2nd feedback) Yes Yes Yes S
(V.)[n].MPA.INPUTREV[g].Xn
Turns of the motor shaft Yes Yes Yes P/S
(V.)[n].MPA.INPUTREV2[g].Xn
Turns of the motor shaft (2nd feedback) Yes Yes — P/S
(V.)[n].MPA.OUTPUTREV[g].Xn
Turns of the machine axis Yes Yes Yes P/S
(V.)[n].MPA.OUTPUTREV2[g].Xn
Turns of the machine axis (2nd feedback) Yes Yes — P/S
(V.)[n].MPA.SINMAGNI[g].Xn
Sinusoidal multiplying factor Yes Yes Yes —
(V.)[n].MPA.ABSFEEDBACK[g].Xn
Absolute feedback system
"0" = No "1"= Yes
Yes Yes Yes P/S
(V.)[n].MPA.FBACKAL[g]
Feedback alarm activation
"0" = No "1"= Yes
Yes Yes Yes —
LOOP SETTING
Lin Rot Spd Ana Ser
(V.)[n].MPA.LOOPCH[g].Xn
Analog voltage sign change
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
(V.)[n].MPA.AXISCH[g].Xn
Feedback sign change
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
(V.)[n].MPA.INPOSW[g].Xn
In-position zone Yes Yes Yes Yes P/S
BACKLASH IN MOVEMENT REVERSAL Lin Rot Spd Ana Ser
(V.)[n].MPA.BACKLASH[g].Xn
Backlash Yes Yes Yes Yes P/S
BACKLASH. ADDITIONAL VELOCITY COMMAND PULSE
Lin Rot Spd Ana Ser
(V.)[n].MPA.BAKANOUT[g].Xn
Additional velocity command pulse Yes Yes Yes Yes P/S
(V.)[n].MPA.BAKTIME[g].Xn
Duration of the additional velocity command
pulse
Yes Yes Yes Yes P/S
(V.)[n].MPA.ACTBAKAN[g].Xn
Application of the additional velocity
command pulse
"0" = G2/G3 "1" = Always
Yes Yes Yes Yes P/S
FEEDRATE SETTING
Lin Rot Spd Ana Ser
(V.)[n].MPA.G00FEED[g].Xn
Feedrate in G00 Yes Yes Yes Yes P/S
(V.)[n].MPA.MAXVOLT[g].Xn
Analog voltage for G00FEED Yes Yes Yes Yes S