Programming manual
402
CNC 8070
14.
CNC VARIABLES
Tool related
(SOFT V02.0X)
382
The following variables may be accessed from the program (PRG), PLC and interface (INT) are
read-write (R/W).
If in the tool variables, the offset number is left out, the variable will then refer to the active offset.
(V.)TM.MZWAIT There is no need to program it in the subroutine associated with M06. The
subroutine itself waits for the manager's maneuvers to finish. This way, block preparation is not
interrupted.
GEOMETRY
Rot
Lin
Spd
(V.)[n].TM.TOR[i]
Radius of the tool offset [i] of the active tool — —
(V.)TM.TORT[m][i]
Radius of the tool offset [i] of the [m] tool — —
(V.)[n].TM.TOI[i]
R wear of the [i] offset of the active tool — —
(V.)TM.TOIT[m][i]
R wear of the [i] offset of the [m] tool — —
(V.)[n].TM.TOL[i]
Length offset [i] of the active tool — —
(V.)TM.TOLT[m][i]
Length of the tool offset [i] of the [m] tool — —
(V.)[n].TM.TOK[i]
L wear of the [i] offset of the active tool — —
(V.)TM.TOKT[m][i]
L wear of the [i] offset of the [m] tool — —
(V.)[n].TM.TOTIPR[i]
Tool tip radius of the [i] offset of the active tool — —
(V.)TM.TOTIPRT[m][i]
Tool tip radius of the [i] offset of the [m] tool — —
(V.)[n].TM.TOWTIPR[i]
Tool tip radius wear of the [i] offset of the active tool — —
(V.)TM.TOWTIPRT[m][i]
Tool tip radius wear of the [i] offset of the [m] tool — —
(V.)[n].TM.TOCUTL[i]
Cutting length of the [i] offset of the active tool — —
(V.)TM.TOCUTLT[m][i]
Cutting length of the [i] offset of the [m] tool — —
(V.)[n].TM.TOAN[i]
Penetration angle of the [i] offset of the active tool — —
(V.)TM.TOANT[m][i]
Penetration angle of the [i] offset of the [m] tool — —
(V.)[n].TM.TOFL[i].Xn
Xn axis deviation of the [i] offset of the active tool Yes No
(V.)[n].TM.TOFL1
Offset of the tool in the first axis of the channel Yes No
(V.)[n].TM.TOFL2
Offset of the tool in the second axis of the channel Yes No
(V.)[n].TM.TOFL3
Offset of the tool in the third axis of the channel Yes No
(V.)TM.TOFLT[m][i].Xn
Xn axis deviation of the [i] offset of the [m] tool Yes No
(V.)[n].TM.TOFLW[i].Xn
Xn axis deviation of the [i] offset of the active tool Yes No
(V.)[n].TM.TOFLW1
Wear offset of the tool in the first axis of the channel Yes No
(V.)[n].TM.TOFLW2
Wear offset of the tool in the second axis of the channel Yes No
(V.)[n].TM.TOFLW3
Wear offset of the tool in the third axis of the channel Yes No
(V.)TM.TOFLWT[m][i].Xn
Xn axis deviation wear of the [i] offset of the [m] tool Yes No
(V.)TM.TOR[i] Radius of active tool, offset [i].
(V.)TM.TOR Radius of active tool, active offset.
(V.)TM.TORT[m][i] Tool radius [m], offset [i].
(V.)TM.TORT[m] Tool radius [m], active offset in the channel.
"CUSTOM" DATA PRG PLC INT
(V.)[n].TM.TOTP1
Additional parameter 1 of the active tool R/W R/W R/W
(V.)[n].TM.TOTP2
Additional parameter 2 of the active tool R/W R/W R/W
(V.)[n].TM.TOTP3
Additional parameter 3 of the active tool R/W R/W R/W
(V.)[n].TM.TOTP4
Additional parameter 4 of the active tool R/W R/W R/W
(V.)TM.TOTP1T[i]
Additional parameter 1 of the [i] tool R/W R/W R/W
(V.)TM.TOTP2T[i]
Additional parameter 2 of the [i] tool R/W R/W R/W
(V.)TM.TOTP3T[i]
Additional parameter 3 of the [i] tool R/W R/W R/W
(V.)TM.TOTP4T[i]
Additional parameter 4 of the [i] tool R/W R/W R/W
TOOL MANAGER PRG PLC INT
(V.)[n].TM.MZSTATUS
Status of the tool manager — R R
(V.)[n].TM.MZRUN
Tool manager running — R R
(V.)[n].TM.MZMODE
Operating mode of the tool manager R/W R R/W
(V.)[n].TM.MZWAIT
Tool manager executing a maneuver R R R
To Next Page
Loading...
