Programming manual
CNC 8070
CREATING A PROGRAM
Programming in ISO code
1.
(SOFT V02.0X)
9
G58 ! * Absolute zero offset 5 4.4
G59 ! * Absolute zero offset 6 4.4
G60 * Square corner (not modal) 7.1
G61 * Controlled corner rounding (not modal) 7.3
G63 * * Rigid tapping 6.8
G70 * ? * Programming in inches 3.2
G71 * ? Programming in millimeters 3.2
G72 * Scaling factor 7.10
G73 * * Coordinate system rotation (pattern rotation) 7.9
G74 * Home search 2.4.2
G80 * * Canned cycle cancellation 10.1.3
G81 * * Drilling canned cycle 10.2
G82 * * Drilling canned cycle with variable peck 10.3
G83 * * Deep-hole drilling canned cycle with constant peck 10.4
G84 * * Tapping canned cycle 10.5
G85 * * Reaming canned cycle 10.6
G86 * * Boring canned cycle 10.7
G87 * * Rectangular pocket canned cycle. 10.8
G88 * * Circular pocket canned cycle 10.9
G90 * ? Programming in absolute coordinates 3.3
G91 * ? * Programming in incremental coordinates 3.3
G92 ! * Coordinate preset 4.3
G93 * * Machining time in seconds 5.2.1
G94 * ? Feedrate in millimeters/minute (inches/minute) 5.2.1
G95 * ? * Feedrate in millimeters/revolution (inches/revolution) 5.2.1
G96 * * Constant surface speed 5.3.1
G97 * * Constant turning speed 5.3.1
G98 * * Withdrawal to the starting plane 10.1.4
G99 * * Withdrawal to the reference plane 10.1.4
G100 * Probing 8.6
G101 * Include probe offset 8.6.1
G102 * Exclude probe offset 8.6.1
G108 * * Feedrate blending at the beginning of the block 5.2.2
G109 * Feedrate blending at the end of the block 5.2.2
G112 * Changing of parameter range of an axis 8.5
G130 * * Percentage of acceleration to be applied per axis 5.2.5
G131 * * Percentage of acceleration to be applied to all the axes 5.2.5
G132 * * Percentage of jerk to be applied per axis 5.2.6
G133 * * Percentage of jerk to be applied to all the axes 5.2.6
G134 * * Percentage of Feed-Forward to be applied 5.2.7
G135 * * Percentage of AC-Forward to be applied 5.2.8
G136 * * Circular transition between blocks 9.1.1
G137 * * Linear transition between blocks 9.1.1
G138 * * Direct activation/cancellation of tool compensation 9.1.1
G139 * * Indirect activation/cancellation of tool compensation 9.1.1
G151 * * * Programming in diameters 3.4
G152 * Programming in radius 3.4
G157 * * Excluding axes in the zero offset 4.4.2
G158 * * Incremental zero offset 4.4.1
G159 ! * Additional absolute zero offsets 4.4
G160 * Multiple machining in straight line 11.1
G161 * Multiple machining in rectangular pattern 11.2
G162 * Multiple machining in grid pattern 11.3
G163 * Multiple machining in a full circle 11.4
G164 * Multiple machining in arc pattern 11.5
G165 * Machining programmed with an arc-chord 11.6
G170 * Hirth axes OFF 8.3
G171 * * Hirth axes ON 8.3
G180 * OEM Subroutine 8.4
G181 * OEM Subroutine 8.4
G182 * OEM Subroutine 8.4
Function M D V Meaning Section
To Next Page
Loading...
