Fagor Evo Concept Series - Use and Maintenance Instructions; Rinse Aid and Detergent Dispensers; Pressure Pump and Recycling

4.6
Hydraulic rinse aid dispenser
Operation:
This dispenser absorbs the rinse aid when it detects a loss in pressure during rinsing.
That is, when the filling solenoid valve closes, a vacuum is created that makes the rinse aid
dispenser
absorb the fluid to which it is connected.
Adjustment:
The dispenser should be adjusted when the machine is installed to ensure that the
wash is optimised from the start. The setting should be adjusted according to the type of rinse aid
and the water hardness.
It is recommended
defined by a technician specialised in the use of chemical products in order
to ensure a more efficient wash.
4.7 Detergent dispenser
This ensures that the correct measure of d
Installation:
the detergent dispenser input must be in the tub of the machine, above the maximum
water level. Please see the electrical circuit diagram for details of the electrical connection. The tub
should have an opening in which the dispenser is fitted. If this is
above the maximum water level to mount the corresponding bushing.
Operation:
the detergent dispenser is activated when the machine is taking water, whether it is in
rinse cycle or whether it is filling.
Settings: the measure o
f detergent used should be adjusted when the component is installed to
ensure that the wash is optimised from the start.
It is recommended
by a technician specialised in the use of chemical
ensure a more efficient wash.
4.8 Pressure pump
If the main
water pressure is
pump. If the pressure is less than 2 bar (200kPa), the machine may operate incorrectly.
electrical connections for the pressure pump are shown in the electric circuit diagram. The water
connection to the pressure pump is shown in
If the mains water pressure is less than 2 bar (200 kPa), please contact your supplier or
manufacturer to request the PRESSURE PUMP KIT.
The pressure pump must only be installed by personnel authorised by the manufacturer,
and the manufacturer does not accept liability in the event of incorrect installation.
4.9 Recycling
The product
packaging consists of:
• A wooden pallet.
• Cardboard.
•
A polypropylene band
•
Expanded polyethylene
All the packaging used around the machine can be recycled; The
will help to protect the environment. For further information regarding the recycling of these products,
please refer to the relevant office of the local body.
current legislation.
5. USE
AND MAINTENANCE INSTRUCTIONS
BEFORE STARTING THE APPLIANCE, PLEASE READ THE INSTRUCTIONS
CONTAINED IN THIS MANUAL CAREFULLY.
THE APPLIANCE IS EXCLUSIVELY FOR PROFESSIONAL USE, AND SHOULD
ONLY BE USED BY QUALIFIED PERSONNEL.
Hydraulic rinse aid dispenser
This dispenser absorbs the rinse aid when it detects a loss in pressure during rinsing.
That is, when the filling solenoid valve closes, a vacuum is created that makes the rinse aid
absorb the fluid to which it is connected.
The dispenser should be adjusted when the machine is installed to ensure that the
wash is optimised from the start. The setting should be adjusted according to the type of rinse aid
It is recommended
that the rinse aid product and the dispenser setting are
defined by a technician specialised in the use of chemical products in order
to ensure a more efficient wash.
This ensures that the correct measure of d
etergent is supplied to the machine.
the detergent dispenser input must be in the tub of the machine, above the maximum
water level. Please see the electrical circuit diagram for details of the electrical connection. The tub
should have an opening in which the dispenser is fitted. If this is
not the case, make a Ø12 hole
above the maximum water level to mount the corresponding bushing.
the detergent dispenser is activated when the machine is taking water, whether it is in
rinse cycle or whether it is filling.
f detergent used should be adjusted when the component is installed to
ensure that the wash is optimised from the start.
It is recommended
that the detergent and the dispenser setting are defined
by a technician specialised in the use of chemical
products in order to
ensure a more efficient wash.
water pressure is
less than 2 bar (200 kPa), you have
the option of installing a pressure
pump. If the pressure is less than 2 bar (200kPa), the machine may operate incorrectly.
electrical connections for the pressure pump are shown in the electric circuit diagram. The water
connection to the pressure pump is shown in
FIGURE 4 (page 5).
If the mains water pressure is less than 2 bar (200 kPa), please contact your supplier or
manufacturer to request the PRESSURE PUMP KIT.
The pressure pump must only be installed by personnel authorised by the manufacturer,
and the manufacturer does not accept liability in the event of incorrect installation.
packaging consists of:
A polypropylene band
.
Expanded polyethylene
.
All the packaging used around the machine can be recycled; The
correct disposal of these products
will help to protect the environment. For further information regarding the recycling of these products,
please refer to the relevant office of the local body.
Dispose of these materials in accordance with
AND MAINTENANCE INSTRUCTIONS
BEFORE STARTING THE APPLIANCE, PLEASE READ THE INSTRUCTIONS
CONTAINED IN THIS MANUAL CAREFULLY.
THE APPLIANCE IS EXCLUSIVELY FOR PROFESSIONAL USE, AND SHOULD
ONLY BE USED BY QUALIFIED PERSONNEL.
35
This dispenser absorbs the rinse aid when it detects a loss in pressure during rinsing.
That is, when the filling solenoid valve closes, a vacuum is created that makes the rinse aid
The dispenser should be adjusted when the machine is installed to ensure that the
wash is optimised from the start. The setting should be adjusted according to the type of rinse aid
that the rinse aid product and the dispenser setting are
defined by a technician specialised in the use of chemical products in order
etergent is supplied to the machine.
the detergent dispenser input must be in the tub of the machine, above the maximum
water level. Please see the electrical circuit diagram for details of the electrical connection. The tub
not the case, make a Ø12 hole
the detergent dispenser is activated when the machine is taking water, whether it is in
f detergent used should be adjusted when the component is installed to
that the detergent and the dispenser setting are defined
products in order to
the option of installing a pressure
pump. If the pressure is less than 2 bar (200kPa), the machine may operate incorrectly.
The
electrical connections for the pressure pump are shown in the electric circuit diagram. The water
If the mains water pressure is less than 2 bar (200 kPa), please contact your supplier or
the
The pressure pump must only be installed by personnel authorised by the manufacturer,
and the manufacturer does not accept liability in the event of incorrect installation.
correct disposal of these products
will help to protect the environment. For further information regarding the recycling of these products,
Dispose of these materials in accordance with
BEFORE STARTING THE APPLIANCE, PLEASE READ THE INSTRUCTIONS
THE APPLIANCE IS EXCLUSIVELY FOR PROFESSIONAL USE, AND SHOULD