16
OF 1010
This distance can be adjusted faster and more
precisely with the fine precision adjustment (3.6),
available as an accessory:
- Turn the adjusting screw (3.4) in the plastic part
of the guide,
- clamp the guide rods with the rotating knobs
(3.5) in the precision adjustment,
- loosen the rotating knobs (3.3) of the parallel
guide,
- set the desired distance with the adjusting screw
and retighten the rotating knobs.
6.4 Routing with the TV-OF extension table
The extension table TV-OF, available as an acces-
sory, can be used to enlarge the support area of
the router and thus improve guidance, e.g. when
routing close to edges.
The extension table is fitted in the same way as
the parallel guide.
6.5 Routing with the FS guide system
The guide system, available as an accessory, fa-
cilitates routing straight grooves.
- Fasten the guide stop (4.1) to the platen with the
guide rails (3.7) of the parallel guide.
- Fasten the guide rail (4.3) with FSZ screw clamps
(4.4) to the workpiece. Make sure that the safety
distance X (Fig. 4) of 5 mm between the front
edge of the guide rail and cutter or groove is
observed.
- Place the guide stop onto the guide rail as shown
in Fig. 4. To ensure a backlash-free guidance of
the router stop you can adjust two guide cheeks
with a screwdriver through the side openings
(4.2).
- Screw the height-adjustable support (4.6) of the
router table’s threaded bore (6.6) in such a way
that the underside of the router table is parallel
to the surface of the workpiece.
When working with marking-up lines, the marks
on the platen (4.5) and the scale on the support
(4.6) show the centre axis of the cutter.
6.6 Routing with the SZ-OF 1000 beam com-
passes
With the SZ-OF 1000 beam compasses, which are
available as an accessory, you can make circular
cuts or segments of circles with diameters from
153 to 760 mm.
- The beam compasses are pushed into the front
groove of the platen until the desired radius is
set.
- Lock the beam compasses with the rotating
knob (1.12).
Practical hint
To prevent the tip of the compasses from making a
hole in the workpiece, fix a thin board at the centre
point by means of double-sided adhesive tape.
6.7 Copy cutting
A copying ring or the copying device is used to
exactly reproduce existing workpieces (both avail-
able as accessories).
a) Copying ring
Fasten the copying rings to the platen instead of
the cover ring (2.1) from below.
When choosing the size of the copying ring (5.1)
make sure that the cutter used (5.2) fits through
the ring’s opening.
The distance Y (Fig. 5) between the workpiece and
template is calculated by
Y = (Ø copying ring - Ø cutter)
2
The copying ring can be centred exactly with the
centring cone ZF-OF (Order No. 486035).
b) Copying device
The angle arm WA-OF (6.5) and copier scanning
set KT-OF, consisting of roller holder (6.2) and
three copying rollers (6.1), are required for the
copying device.
- Screw the angle arm at the desired height in the
platen’s threaded bore (6.6) with the rotating
knob (6.4).
- Fit a copying roller in the roller holder and bolt
this to the angle arm with the rotating knob (6.3).
Make sure that the copying roller and cutter have
the same diameter!
- Turn the adjusting wheel (6.7) to adjust the dis-
tance between the copying roller and cutter axis.
6.8 Edge band trimming
Protruding edge bands can be flush trimmed with
the angle arm WA-OF (7.6) in connection with the
guide plate UP-OF (7.3).
- Screw the angle arm into the platen’s threaded
bore (7.7) with the rotating knob (7.5).
- Bolt the guide plate to the angle arm with the
rotating knob (7.4).
- Adjust the milling depth so that this is equal to
the thickness of the edge band + 2 mm.
- Move the guide plate (8.1) as close as possible to
the cutter by loosening the rotating knob (8.3).
- Adjust the depth of the guide plate with the
adjusting wheel (8.2) so that during trimming
a few decimillimetres of the edge band are left
protruding which can then be sanded down by
hand.
To Next Page
Loading...
