Instruction Manual
D103557X012
Parts
April 2016
72
Kit Description Part Number
7* Spare Module Base Assembly Kit
[kit contains module base (key 2); drive screws, qty. 2,
(key 11); shield/label (key 19); hex socket cap screw, qty. 3,
(key 38); self tapping screw, qty. 2 (key 49); pipe plug, qty. 3
(key 61); retaining ring, qty. 3 (key 154); screen (key 236);
and flame arrestors, qty. 3 (key 243)]
Aluminum GE18654X012
Stainless Steel GE18654X022
8* Spare Housing Assembly Kit
[kit contains housing (key 1); vent assembly (key 52);
seal (only included in Housing A kits) (key 288);
seal (key 237); O‐ring (key 34); O‐ring (only used
with integrally mounted regulator) (key 5)]
Aluminum
Housing A (used for GX actuator) GE48798X042
Housing B (used for all actuators except GX) GE48798X082
Stainless Steel
Housing B (used for all actuators except GX) GE48798X102
9* Spare I/P Shroud Kit
[kit contains shroud (key 169) and
hex socket cap screw, qty. 4 (key 23)] GE29183X012
10* Remote Mount Feedback Unit Kit (see figure 7‐5)
[remote housing assembly (key25); hex socket set
screw (key 58); 1/2 NPT pipe plug (key 62); wire retainer, qty 2
(key 131); terminal cover (key 255); o-ring (key 256); gasket
(Housing A only, used for GX actuator) (key 287); seal
(Housing A only, used for GX actuator) (key 288)
Note
The remote mount feedback kit is not orderable by part number due to
nameplate/approval requirements. Contact your Emerson Process
Management sales office for information on ordering this kit.
11* Feedback Array Kit
Sliding Stem (Linear)
[kit contains • feedback array and hex socket cap screws, qty.2,
washer, plain, qty.2, external tooth lock washer, qty.2 (only with
aluminum feedback array kit) and alignment template.
• 210 mm (8-1/4 inch) kit contains feedback array and hex
socket cap screws, qty. 4,washer, plain, qty. 4, external tooth
lock washer, qty. 4 (only with aluminum feedback array kit),
alignment template and insert]. Stainless steel kits only for use
with stainless steel mounting kits.
7 mm (1/4-inch)
Aluminum GG20240X012
19 mm (3/4-inch)
Aluminum GG20240X022
Stainless steel GE65853X012
25 mm (1-inch)
Aluminum GG20240X032
Stainless steel GE65853X022
38 mm (1-1/2 inch)
Aluminum GG20240X042
Stainless steel GE65853X032
Kit Description Part Number
11* Feedback Array Kit
50 mm (2-inch)
Aluminum GG20240X052
Stainless steel GE65853X042
110 mm (4-1/8 inch)
Aluminum GG20240X082
Stainless steel GE65853X062
210 mm (8-1/4 inch)
Aluminum GG20243X012
Stainless steel GE65853X072
Rotary
[Kit contains feedback assembly, pointer assembly, travel
indicator scale and M3 machine pan head screws qty.2].
Stainless steel kits only for use with stainless steel mounting kits.
Aluminum GE71982X012
Stainless steel GE71982X022
12 Mounting Shield Kit
[kit contains shield, qty. 3 and machine
screws, qty. 6] GG05242X022
13* Gasket/Seal Kit, for use with GX actuator
[kit contains insulating gasket (key 287)
and seal (key 288)] GE45468X012
Parts List
Note
Contact your Emerson Process Management sales office for Part
Ordering information.
All DVC6200 SIS parts with elastomers include extreme temperature
fluorosilicone elastomers.
Parts with footnote numbers shown are available in parts kits; see
footnote information at the bottom of the page.
Key Description
Housing (see figure 7‐2 and 7‐4)
DVC6200 SIS and DVC6205 SIS
1 Housing
(8)
11 Drive Screw (2 req'd) (DVC6205 SIS only)
20 Shield (DVC6205 SIS only)
52 Vent, plastic
(2)
74 Mounting Bracket (DVC6205 SIS only)
248 Screw, hex head (4 req’d) (DVC6205 SIS only)
249 Screw, hex head (4 req’d) (DVC6205 SIS only)
250 Spacer (4 req’d) (DVC6205 SIS only)
267 Standoff (2 req’d) (DVC6205 SIS only)
271 Screen
(8)
287 Gasket, Housing A only (used for GX actuator) (DVC6200 SIS only)
288 Seal, Housing A only (used for GX actuator) (DVC6200 SIS only)
*Recommended spare parts
2. Available in the Small Hardware Spare Parts Kit
8. Available in the Spare Housing Assembly Kit
To Next Page
Loading...
