Fisher Studio-Standard CR-W50 - Recording and Dubbing Operations; Erasure (Deck 2); Synchro Dubbing from Deck 1 to Deck 2

6. Set the DECK-2 TAPE SELECTOR switches according
to the type of tape being used (METAL, Cr02 or
NORMAL).
7.
Depress the r eft-hand DOLBY NR sw i tch if you wish to
record with the noise reduction system. If you wish to
record with the Dolby C-type, depress the right-hand
DOLBY NR switch too. The DOLBY-C ir:!dicator will
light up.
8. Push the RESET
button of the tape cou nter to reset to
"000."
9. Depress the PAUSE button of DECK 2.
10 . Depress the REC button and while holding . it, depress
the PLAY button. DECK 2 is now ready for recording .
11 . Adj, ust the recording level with the INPUT LEVEL con-
trols so that the "a dB" INPUT LEVEL indicators are il-
luminated . Refer to RECORDING LEVEL ADJUST-
MENT
section .
12 . After setting the proper recording levels, start record-
ing by depressing the PAUSE button a second time.
You are now
recording. If you wish to stop record ing
temporarily without resetting the REC and PLAY but-
tons, depress the PAUSE button. Depress the PAUSE
button again to resume recording .
13 . When recording is finished, depress the STOP/EJECT
button once. If the tape is wound completely to the
right hand reel while recording , DECK 2 will stop auto-
matically .
14. To
record side 2 of the tape, depress the STOP/EJECT
button twice to eject the cassette. Turn the cassette
over, reinsert it and close the compartment lid. To
begin
recording again, repeat steps 6 to 13.
15 . Release the POWER switch to the OFF position .
ERASURE (DECK 2)
During recording with DECK 2, all· previously ~ecorded
material is erased automatically . If you wish to erase with-
out recording new material, follow this procedure:
1. Insert the cassette property with the s,ide to be erased
facing you.
2. Release the SYNCHRO START
switch to the SEQ.
PLAY
position .
3.
Slide the LEFT and RIGHT INPUT LEVEL controls to
the "a" position .
4.
Set the DECK-2 TAPE SELECTOR switches according
to the type of tape being used (METAL, Cr02 or
NORMAL).
5.
Depress the REC button and while holding it. depress
the PLAY button of DECK 2. The side of the tape facing
you will be erased .
6.
To stop tape transport , depress the STOP/EJECT
button of DECK 2.
7.
To erase the other side, turn the cassette over and
repeat steps 1 through 6.
SVNCHRO DUBBING F,ROM DECK 1 TO DECK 2
First. depress the TAPE MONITOR switch of the amplifier .
Make sure that you turn down the VOLUME control on the
amplifier before operating both decks .
1.
Depress the POWER switch to the ON position.
2.
Depress the SYNCHRO START switch to the
DUBBING
position .
3.
Depress the STOP/EJECT button of DECK 1. Inse rt a
pre - recorded cassette into the compartment with the
side to be' played facing you. Close the compartment
lid of DECK 1.
4. Depress the
STOP/EJECT button of DECK 2. Insert a
cassette into the compartment with the side to be
recorded facing you. When using an unrecorded
cassette, t'he fu II reel will be on the left side . Close the
compartment ,lid of DECK 2.
5. Set the
DECK-2 TAPE SELECTOR switches according
to the type of tape being used (METAL, Cr02 or
NORMAL).
6. Push
the RESET button of the tape counter to reset to
"
000."
7. To set to standby mode for synchro dubbing, depress
the REC button and while hold ing it, depress the PLAY
button of DECK 2.
8.
Start synchro dubbing by depressing the PLAY button
of DECK 1. You are now dubbing.
9. To stop dubbing temporarily, depress the PAUSE
button of DECK 1. DECK 1 and DECK 2 will stop simul-
taneously . Depress the PAUSE button of DECK 1 again
to
resume dubbing.
10 . During dubbing, to use the ASF system on DECK 1,
depress the F-FWD or REW button of DECK 1. During
ASF program search operation, DECK 2 is set auto-
matically to the standby mode. After program search is
completed , DECK 2 starts automatically and synchro
dubbing will resume .
11 . When dubbing is finished , depress the STOP/EJECT
buttons of DECKS 1 and 2 once. If the tape is wound
completely to the right hand reel while dubbing,
DECKS 1 and 2 will stop automatically .
12 . To dub side 2 of the tape, depress the STOP/EJECT
buUons of DECKS 1 and 2 twice to eject the cassettes.
Turn the cassettes over, reinsert them and close the
compartment lids. To begin dubbing again, repeat
steps 5 to 11.
13. Release the POWER
switch to the O~F position .
NOTE:
When dubbing from DECK 1 to DECK 2, the Dolby NR
circuits are automatically set in the OFF position even
with the left-hand DOLBY NR switch depressed to the
ON position or both DOLBY NR switches depressed.
When a tape recorded with the Dolby NR system is
played
back with DECK 1, the Dolbyized sounds are
directly dubbed into DECK 2. However, the sounds
reproduced through the speakers connected to the
amplifier and PHONES jack will be excessively empha-
sized in the treble range while the dubbing process is
in
progress .
The INPUT LEVEL
indicators show the playback level
of DECK 1 during dubbing.
IMPORTANT NOTE:
In case the length of the tape inserted in DECK 1 is
shorter than that of the tape inserted in DECK 2,
the PLAY
button of DECK 1 is released automati-
cally at the end of the tape and the recording oper-
ation will stop simultaneously. To stop DECK 2,
depress the STOP/EJECT button of DECK 2.
If the length or the tape inserted in DECK 2 is
shorter than that of the tape inserted in DECK 1,
the RECORD and
PLAY buttons of DECK 2 will be
released
automatically at the end of the tape. But
DECK 1 will continue to play back until it reaches
its end.
9