FlySky FS-R7P - Failsafe Protection; Failsafe Modes and Notes; Important Precautions; Safety and Installation Cautions

FS-R7P
接收机 Receiver
Http://www.󽗊ysky-cn.com
Copyright ©2022 Flysky Technology co., ltd
注意事项：
• 使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
• 关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时，接收机仍然在工作，将会导致遥控设备失控。失控保
护设置不合理可能引起事故。
• 确保接收机安装在远离电机或电子噪声过多的区域。
• 接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有1厘米以上的距离。
• 准备过程中，请勿连接接收机电源，避免造成不必要的损失。
失控保护
Failsafe
Attentions:
• Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
• Make sure the receiver's battery is disconnected before turning o󽗈 the transmitter, failure to do so can result out of control.
Unreasonable setting of the Failsafe may cause accidents.
• Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical
noise.
• Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
• Do not power on the receiver during the setup process to prevent loss of control.
失控保护功能用于在接收机失去信号不受控制后，接收机按设置好的失控保护值进行通道输出以保护模型及人员安全。
本款接收机共支持两种失控保护模式 : [ 无输出 ] 和 [ 有输出 ]
[ 无输出 ] i-BUS/PPM/PWM 通道接口为无输出状态 ;
[ 有输出 ] i-BUS/PPM/PWM 通道接口输出设置的固定值。
注：
1. 因为 S.BUS 信号包含失控标志位，所以接收机可通过失控标志位将“失控状态”信息传递到后续设备，而无需通过 [ 无输出 ] 状态传递（后续设备通
过解析失控标志位信息做出相应地应对即可）；
2. 对于无失控标志位的信号 PWM/PPM/i-BUS，支持设置失控时信号 [ 无输出 ]，通过 [ 无输出 ] 状态将“失控状态”信息传递给后续设备。
The failsafe function is used to output the channel value according to the out-of-control protection value set by the user after the receiver
loses its signal and is out of control to protect the model and personnel.
It can also be set failsafe for each channel respectively. This receiver supports two failsafe modes: [ON]and [OFF]
[OFF] It is no output for the interface of i-BUS/PPM/PWM.
[ON] Outputs the failsafe values set for the interface of i-BUS/PPM/PWM.
Notes:
1. Because the S.BUS signal information contains failsafe 󽗊ag bits, the failsafe information can be transmitted to the subsequent devices by the failsafe 󽗊ag
bits ruther than by OFF state. The subsequent devices gives response according to the analysed information for the failsafe 󽗊ag bits.
2. For the signal PWM/PPM/i-BUS without failsafe 󽗊ag bits, it supports the setting of the output signal to OFF in case of failsafe, transmitting the failsafe
information to the subsequent devices by OFF state.