To Next PageTo Next PageHow to fix FM Mattsson 9000E Tronic WMS 1650-1000 Plumbing Product when no water comes out?
If no water is coming out of your FM Mattsson Plumbing Product, there could be several reasons: * Insufficient supply voltage: Replace the battery or check the voltage. * Blocked inlet filters: Clean the inlet filters. * Blocked solenoid valve filter: Clean the solenoid valve. * Defective solenoid valve: Replace the solenoid valve.
How to increase the water pressure in my FM Mattsson 9000E Tronic WMS 1650-1000?
If the water pressure in your FM Mattsson Plumbing Product is too low, the following could be the causes: * Blocked aerator: Clean or replace the aerator. * Blocked inlet filters: Clean or replace the inlet filters. * Blocked solenoid valve filter: Clean or replace the solenoid valve.
What to do if my FM Mattsson 9000E Tronic WMS 1650-1000 mixer does not turn off?
If your FM Mattsson Plumbing Product mixer does not turn off, consider these potential causes and solutions: * Extended/sustained flushing activated: Press a finger against the ring on the sensor to turn the water off, or wait up to 60 seconds for the water to stop running. * Hygiene flush in progress (yellow LED is flashing): Wait 3 to 30 minutes or briefly disconnect the power supply. * Wrong solenoid valve: Replace the solenoid valve. * Flush time set too high: Wait up to 30 seconds then reset the sensor.
Why is the temperature wrong on my FM Mattsson 9000E Tronic WMS 1650-1000 Plumbing Product?
If the temperature of your FM Mattsson Plumbing Product is not correct, consider the following: * Incorrect water pressure and temperature: Set the temperature value to the coldest/hottest setting and check that the water pressure and temperature are high enough. * The temperature limiter function is set incorrectly: Set the temperature limiter to its hottest setting and check the temperature. Adjust the temperature limiter.
Why is water dripping from my FM Mattsson 9000E Tronic WMS 1650-1000 Plumbing Product mixer's spout/shower?
If water is dripping from your FM Mattsson Plumbing Product mixer's spout or shower, here are possible reasons: * Leaking solenoid valve: Replace the solenoid valve. * Water residue in overhead shower head: Adjust the overhead shower head to a horizontal position.
What does it mean when the sensor flashes red and doesn't work on FM Mattsson 9000E Tronic WMS 1650-1000?
If the sensor on your FM Mattsson Plumbing Product flashes red and doesn't work, it likely indicates a flat battery. Replace the battery to resolve this issue.
Why doesn't my FM Mattsson 9000E Tronic WMS 1650-1000 Plumbing Product mixer respond when I adjust the temperature?
If your FM Mattsson Plumbing Product mixer does not respond when you adjust the temperature, it may be due to incorrect connection or installation. Ensure the hot water is connected to the left side of the mixer.
Why is the sensor flashing yellow but still working on my FM Mattsson 9000E Tronic WMS 1650-1000?
If the sensor on your FM Mattsson Plumbing Product flashes yellow but still works, it means the battery is low. Replace the battery.
Why does my FM Mattsson 9000E Tronic WMS 1650-1000 mixer start running without being turned on?
If your FM Mattsson Plumbing Product mixer starts running without being turned on, it is likely in hygiene flush mode (indicated by a flashing yellow LED). Turn off the hygiene flush mode via WMS.
Why does the shower duration vary on my FM Mattsson 9000E Tronic WMS 1650-1000 Plumbing Product?
The shower may run up to 5 minutes on your FM Mattsson Plumbing Product if the user is close to the mixer. To change the programme or settings, use WMS.
General| Power Supply | 24V AC/DC |
|---|---|
| Brand | FM Mattsson |
| Category | Plumbing Product |
| Material | Brass |
| Series | 9000E |
| Article Number | 1650-1000 |
| Model | Electronic |
| Water Pressure | 0.5 - 10 bar |
| Certification | CE |
Guides installation by a professional plumber for safe and correct setup.
Details electrical connection requirements and local regulations for mains operation.
Provides instructions for protecting the mixer from frost damage in cold conditions.
Explains how to clean the mixer's surface to maintain its finish and remove lime spots.
Emphasizes the importance of leak checks according to industry standards.
Indicates where to find information on ordering replacement parts.
Informs about returning disused products for recycling.
Presents detailed technical specifications, standards, and connection details for the mixer.
Provides step-by-step instructions for attaching the mixer spout.
Explains how to pause or stop flushing cycles, often indicated by LED status.
Details how to activate or cancel extended flushing periods.
Describes how to set and adjust the maximum temperature limit on the thermostat.
Explains how to set and adjust the maximum temperature limit on the mixer valve.
Details various programming options and settings for basin mixers.
Details various programming options and settings for shower mixers.
