Force DIABLO User Manual

PARTS INCLUDED IN SET
Please read this manual guide carefully before usage, and safe keep it
during the validity of the product for viewing at any time.
60 cm
Position the magnet on the wire closest to the fork at the same height
as the sensor. Secure the threaded contact.
The cable must be inserted into the specied groove.
Check that signal transmission is running smoothly.
T
3. Place the transmitter on the side with sign "sensor"
closer to the magnet (on the inner side)
magnet
not
3. For accurate measurement seat on bicycle
while measuring (reccomended instalation in 2 people)
:
adhesive pad
60
FUNCTIONS
Riding time (RTM)
Indicates riding time since last data reset.
Trip distance (DST)
Indicates the distance travelled since the last data reset.
Average speed (AVS)
It is calculated from the measured km/h and total riding time since
last data reset.
Total riding time (TTM)
Indicates the total riding time it can be set in the SET UP mode.
Total distance (ODO)
Indicates the total number of travelled km. It can be set in SET UP
mode.
Maximum speed (MXS)
Indicates the maximum measured speed since the last data reset.
Speed comparsion
An arrow in upper right corner indicate when you are riding faster or
slower than your average speed.
Dodavatel / Importer
KCK Cyklosport-Mode s.r.o.,
Bartošova 348, 765 02 Otrokovice-Kvítkovice, CZ
www.kckcyklosport.cz, www.force.bike
Země původu Čína / Made in China
Data display mode
Display backlight (EL)
For activation of backlight mode přes both buttons M+S (MODE+SET) in
the same time. Display shows “LIGHT ON“ and lights for 10 seconds. When
the backlight is on evreytime you press any button – lights for 10 seconds.
For deactivation of backlight mode press both M+S buttons in same time
again. Display shows “LIGHT OFF“ and function is locked.
cable Micro USB
Art. 452106
wireless computer
transmiter
Art. 391220
RTM trip time
DIST trip distance
AVS average speed
TTM total trip time
ODO total trip distance
MXS maximum speed
CLOCK
ACTUAL SPEED
LED BACKLIGHT
SPEED COMPARSION
AUTO ON/OFF
AUTO ON/ OFF:
Computer automatically enters standby mode after 4 minutes when it
does not measure speed (KMH). Again it starts automatically after
10 seconds of pressing the button or movement - measuring speed.
Always pay attention to the road and trac while riding.
Check regularly the distance between sensor and magnets.
Wireless interference may occur near: smart phones, computers,
Power banks, lights, other wireless devices, high voltage sources,
railroad crossings etc.
Always dismount the computer while cleaning
the bicycle and storage outside (protect from rain and snow).
Battery capacity can be reduced to approximately 70-80%
after 300-500 charging cycles. Battery capacity decreases at lower
temperature. Do not expose the computer to a high temperature
of + 40 ° C (hot place in the car), low temperatures below 0 ° C, high
humidity and direct sunlight. Store in a cool, dry place, keep away from
children, heat source and inammable material. Protect from re and
inammable substances.
Do not submerge in water.
Computer is water-resistant, it can be used in light rain.
During heavy rain, it´s recommended to store in a dry place.
Do not clean with water or aggressive cleaners.
Do not disassemble or otherwise modify the computer,
battery and accessories.
Dispose the computer and battery ecologically
according to valid regulations. Always follow applicable trac laws
in the country where you use the product.
NOTE
Location of computer and accessories
To reset the measured data, press the SET button for 3 seconds.
A RESET warning will appear, which will blink twice.
Data is erased to 0.
5. Possible wireless
signal interference
caused by
electromagnetic waves
(description in notes
- 7/page 13) near the
computer.
4. If transmitting
distance is too long
or angle is incorrect
3. Check wheel
circumference is
correct or not
2. Distance between
speed sensor and
magnet seat correct
or not
No speed display
of faulty display
Malfunction display
Set up again referring
to setup manual
1. Computer is under
set up status
1. Low level battery
2. Computer has been
exposed to high ambient
temperature or direct
sunlight.
1. Charge battery
2. Place the computer
in a lower ambient
temperature
environment.
Display slowly
update
Climate temperature
is low
Place it in normal
temperature
No display, dark or
badly readable.
1. Set up adjust
procedure
2. Refer to
installation to
adjust position.
3. Setting
adjustment
numerical value
referring to wheel
4. Adjust distance
and angle per
installation manual
5. Place computer
far from the source
of electromagnetic
waves.
WARRANTY
Warranty does not apply to damage due to high and low temperatures,
physical damage resulting from abuse, improper repair, improper t,
alternations of the xture or improper use. Supplier does not accept any
liability for injuries or other damage resulting from improper use
of this product under any circumstances. Specications and designs
may be changed without prior notice. The current version of the manual
and declaration of conformity can be found on the website
www.FORCE.BIKE
Speed sensor: non-contact type magnetic sensor
Wireless data transmission: coded 125KHZ low-frequency transmission
Battery type: Lithium polymer 301535/ 120 mAh (0,45Wh)/ 4.2V
Charging: with Micro USB 2.0 cable with battery and charging
status indicator, charging time 1-2h
Computer weight with holder: 38g, battery weight: 10g
Wheel circumference unit: mm
Operating temperature: 0˚ C – 40˚ C, IP protection: IPX6
material: plastic, length 65mm, width 40mm, height 17mm
Measured data
Current speed
Maximum speed
Average speed
Trip distance A
Trip distance B
Total distance
Elapsed time
Clock time
Meausuring range
1.0KM/H--99.9KM/H(MPH)
1.0KM/H--99.9KM/H(MPH)
1.0KM/H--99.9KM/H(MPH)
0.1-99999.9KM(MILE)
0.1-99999.9KM(MILE)
1-999999KM(MILE)
0:00.00-99H:59M:59S
0:00-23:59
22
PAP
You have two options how to enter the settings:
a) Settings menu opens automatically when the battery is insert and
you can set up all values.
b) You can enter the setting mode by press and hold “M“ button for 3
seconds. Then you can set up all values.
To choose an option press “S“ button. To conrm value press “M“
button.
Unit setting (KMH / MPH)
Wheel size Total riding distance
Total riding time
12/24 setting
Clock setting
Wireless computer
FORCE DIABLO, 11 functions, USB
Plastic strap 4x
Possible to set up KMH or MPH units.
Possible to set up 12 or 24 mode of clock.
Place round self-adhesive pad
from bottom side of holder.
Mount the holder on handlebars
and tight with rubber O-ring. For
mounting holder on the stem
change the position of holder like
on the picture bellow.

Force DIABLO Specifications

General

Brand	Force
Model	DIABLO
Category	Bicycle Accessories
Language	English