Ford Performance M-15200K-BML

Need help?

Do you have a question about the Ford Performance M-15200K-BML and is the answer not in the manual?

Summary

Ford Bronco Mirror Spot Lights Installation

Remove Accessory Mounting Point Bolt

Remove the accessory mounting point bolt from both sides of the vehicle.

Position and Install Spot-Lamp Mounts

Position the RH and LH spot-lamp mounts and install the bolt and washers, do not tighten yet.

Secure Spot-Lamps to Mounts

Install the spot-lamps to the mounts and secure each lamp with two bolts, washers, and Nyloc nuts.

Adjust Lamp Aiming and Lateral Position

Adjust lamp aiming and lateral position to preferable position, away from antenna. Torque to 4.8 Nm.

Open Hood and Disconnect Battery

Open the hood and disconnect the battery cable to ground.

Route Power and Ground Wires

Route the power and ground wires under the mirror assembly and into the engine compartment on both sides.

Attach Ground Wires to Bolts

Attach the RH and LH ground wires to the ground bolts (one each side). Torque to 12 Nm.

Route Power Wires Under Cowl Panel

Route power wire from RH and LH sides under cowl panel to blunt end wires on LH side. Reinstall retainers.

Splice Power Wires

Splice the power wires to the VT-GN blunt wire (one of the 6 blunt wire leads bundled together).

Reconnect Battery and Test Lights

Reconnect battery cable to ground. Torque to 48 lb.in (5.4 Nm). Test spot lights.

The provided manual describes the installation and features of the M-15200K-BML 2021 Bronco Mirror Spot Lights for Ford Performance vehicles. This accessory kit is designed to enhance visibility and provide additional lighting for off-road or demanding driving conditions.

Function Description:

The Ford Performance Mirror Spot Lights are auxiliary lighting units intended to be mounted on the side mirrors of a 2021 Ford Bronco. Their primary function is to project focused light, supplementing the vehicle's standard headlights and providing improved illumination of the surrounding terrain. This is particularly beneficial for off-road driving, navigating dark trails, or in situations where a wider or more intense light spread is required. The lights are designed to be controlled via an upfitter switch, allowing the driver to activate them as needed. The installation process involves routing power and ground wires, securing the light assemblies to the mirror mounts, and making electrical connections within the engine compartment. The design allows for adjustment of the lamp aiming and lateral position to optimize the light spread and avoid interference with other vehicle components like the antenna.

Important Technical Specifications:

The kit includes the following components and their quantities:

Spot Light Assembly: 2 units
Bolt: 2 units
Washer: 2 units
Mounting Bracket: 2 units
M6 Nyloc Nut: 4 units
M6x22mm Socket Head Bolt: 4 units
M6 Flat Washer: 4 units

Torque specifications for installation:

Lamp aiming and lateral position adjustment: 4.8 Nm (42.4 lb-in)
Ground wire attachment: 12 Nm (106 lb-in)
Battery cable reconnection: 5.4 Nm (48 lb-in)

The power wires are to be spliced into a VT-GN blunt wire, which is part of a bundle of six blunt wire leads. The lights are designed to be operated using upfitter switch #3.

Usage Features:

Enhanced Visibility: Provides additional, focused lighting for improved visibility in low-light conditions, off-road driving, or adverse weather.
Adjustable Aiming: The spot lamps can be adjusted for both aiming and lateral position, allowing users to customize the light spread according to their specific needs and preferences. This adjustment is facilitated by a slot in the mounting bracket.
Integrated Control: Designed to integrate with the vehicle's existing upfitter switch system (specifically switch #3), offering convenient control from the cabin.
Durable Construction: While not explicitly detailed, the use of Nyloc nuts and specific torque values suggests a design intended for secure and robust mounting, suitable for the demands of off-road environments. The visual representation of the spot light assembly shows a "RIGID" brand, known for its durable off-road lighting solutions.

Maintenance Features:

Installation Instructions: The manual provides detailed, step-by-step instructions for installation, including visual aids, ensuring proper setup.
Torque Specifications: Specific torque values are provided for critical fasteners, which is crucial for ensuring the longevity and secure attachment of the components, reducing the likelihood of loosening due to vibration or impacts.
Warranty Information: Users are directed to https://www.performanceparts.ford.com for warranty information, indicating manufacturer support for the product.
Technical Support: A dedicated Techline (1-800-367-3788) is available for questions, offering direct support for installation or operational issues.
Shop Manual Access: Users can purchase Ford Factory Shop Manuals via www.motorcraftservice.com for more in-depth vehicle information, which might be useful for understanding the vehicle's electrical system or other related components.
Battery Disconnection: The installation procedure includes disconnecting the battery cable to ground, a standard safety measure during electrical work, which helps prevent accidental short circuits or damage to the vehicle's electrical system.
Pre-Reinstallation Check: The final step before reinstalling all parts is to switch on upfitter switch #3 and verify that the spot lights turn on, allowing for immediate troubleshooting if there are any wiring issues.

The overall design emphasizes a robust and integrated accessory solution for the 2021 Ford Bronco, focusing on ease of installation and functional enhancement for specific driving conditions.