Overlap Apex Shed
6' x 4'
Important :
Assembly of this
shed requires a
minimum of two
adults.
Issue 0115
B
OPA4PE
PLAIN END
OPA6WS
WINDOW PANEL
17917658
ROOF SHEET
QTY 2
D
E
F
A
OPA46 PARTS LIST
BRDFL46
FLOOR
SDRPT
DOOR
OPA4DE
DOOR END
84996
PLASTIC GLAZING STRIP QTY 3
44161570PT
1570mm C/STRIP QTY 4
H
M
J
45281753PT
1753mm BATTEN QTY 1
G
Place the corner strips so that they cover the joins
between the panels. Fix each in place using 3 x 30mm
screws
A
4
11
C
OPA6PS
PLAIN SIDE
J
3
REQUIRED TOOLS :
(NOT SUPPLIED)
POZI DRIVE
SCREWDRIVER
TAPE MEASURE
HAMMER
N
L
51120810PAII58PT
810mm BARGE BOARD QTY 4
K
Place the window from the outside so that the lip sits on
the bottom board as shown.
Place the plastic strips around the window so that one
side butts up against the cladding.
Fix the strips and the window in place using 2 x security
screws for each strip and one for the top of the window.
Lip
Board
H
PCWIN1
GLAZING
QTY 1
H
Top View
C
B
D
Must Pre-drill for
each screw used.
37281791PT
1791mm BATTEN QTY 2
L
FEL
T
85052 QTY 1
A
N
Fixing Pack (OPA46FP)
This fixing pack is used for several products.
There may be additional fixings.
Not to Scale
Flush Hinge
Qty 2
50mm Screw Qty 24
30mm Nail Qty 45
25mm Screw Qty 17
Hasp &
Staple
30mm Screw Qty 19
25mm Security Screws
Screws Qty 7
10mm Felt tacks
Qty 100
I
FIN20010512PT
Finial
QTY 1
20121695PPT
20 x1695mm STRIP QTY 1
O
E
SHARP KNIFE
40mm Screw Qty 12
IMPORTANT, RETAIN FOR FUTURE REFERENCE; READ
CAREFULLY
This buildings is pressure treated to ensure longevity of all
timber components and to protect against rot. This may leave
a colour difference on some parts that will even out as the
moisture content stabilises. This will not need additional
treatment.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Due to the nature of the material the doors may need some
trimming for a neater fit.
- Please keep all plastic bags and small parts away from
children
- The roof of this building is not a load bearing structure.
- This product must be built on a solid level base.
Technical Helpline: 0333 7777 089 8.30 am and 5.00
pm Monday to Friday.
Please check all parts prior to assembly
Assembly of damaged parts may be deemed to be
acceptance and this may affect the remedies you are entitled
to.
If the product is not constructed in accordance with the
instructions, or is altered in anyway (e.g. painted), the
manufacturer cannot be held liable for any resulting damage.
Place the panels on top of the floor. Make sure that all the panels are tight and flush before
fixing them to each other using 3x50mm screws.
Before fixing the panels to the floor using 50mm screws, take care and make sure that they are
all sitting flush. All of the screws should be positioned so that they screw into the bearers
underneath.
3x50mm screws for the plain and window sides.
2x50mm screws for the plain and door ends.
Using a scissors carefully cut
one of the plastic strips to
559mm.
Attention:
Take care when placing
the screws. These can
not be backed out.
FLAT HEAD
SCREWDRIVER
SCISSORS
2
Fix the 20 x 1695mm strip to the side
of the door frame so that it is tight
with the cladding and flush with the
frame. Use 3 x 30mm screws.
O
a
b
Place the hinge against the inside of the door frame and
position the large section of the hinge so that it is flush
with the inside of the framing as shown. Fix with 25mm
screws.
Open the hinge and fix the smaller section to the door
framing. Again make sure that the hinge is flush and that
the holes are positioned so that the 25mm screws locate
correctly into the batten.
A
F
To Next Page
Need help?
General
