Hall sensor
GLASSES
CHINA/CRYSTAL
ECO WASH
CYCLES
NORMAL WASH
CLEAN
WASH 1
8 MIN.
TIME
IN
MINUTES
RINSE 1
11 MIN.
RINSE 2
11 MIN.
RINSE 3
11 MIN.
RINSE 4
11 MIN.
RINSE 5
11 MIN.
RINSE 6
15.5 MIN.
DRY *(HOT OR COOL)
22 MIN.
WASH 2
32 MIN.
DRYING
SANITIZED
WASHING
SENSING
LED
BK.......................... Black
BU............................Blue
PK............................Pink
R...............................Red
R-BK...............Red/Black
W............................White
Wiring Diagram
Display Codes (LED)
To start
To delay start
Close and latch door. Press START/CANCEL pad.
Close and latch door. Press DELAY START pad to
select desired delay time.
To select a new
cycle or option
Press desired cycle and/or option pad. The indicator
lights will change. Press START/CANCEL within 15
seconds to begin cycle.
To cancel cycle Press START/CANCEL. Dishwasher will drain for
90 seconds, then shut off.
For controls
lock . . . . . . . . . . .
Press and hold the RINSE ONLY or AIR DRY
pad for 3 seconds. To unlock, press and hold the
RINSE ONLY or AIR DRY pad for 3 seconds.
SENSING
WAS HIN G
SANITIZED
DRYING
CLEAN
OPTION LED's Flashing
STATUS LED's Flashing
---------------------- Turbidity sensor is checking the condition of the wash/rinse water.
No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL.
---------------------- Wash portion of cycle.
-------------------- The SANITIZED criteria has been met. Indicator light will switch off when door is opened.
------------------------ Drying portion of cycle.
------------------------ Shows completion of cycle. Indicator light will switch off when door is opened.
-- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing indicates power failure has
occurred. Press START/CANCEL pad and reselect desired options and cycle.
-- The STATUS LED's that are lit when the door is opened will flash. Close door.
RINSE AGENT LOW ------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is filled.
ER/CE....Configuration Error
ER/uo.....Vent will not close
ER/uF.....Fan not running
PUMP MOTOR
DRAIN MOTOR
VIO
120VAC
60HZ
USER INTERFACE SWITCH
ELECTRONIC
CONTROL
BOARD
P3-2
P6
BU
DISPENSER
R-Y
W
P3- 3
W
W
HEATER
W
HI-LIMIT
THERMOSTAT
TURBIDITY SENSOR/
THERMISTOR
R
P1
WAT E R VA LVE
FLOAT
SWITCH
PK
P3- 1
W
Y
P3-7
P3-8
RINSE AID
LEVEL SENSE
BK
BK
P2- 8
P2- 7
P3-4
P-5
P3-6
DOOR
SWITCH
W
NEUT W
L1 BK
BK
BK
P3-5
P1
BK
P2-1
W
P2-2
R
P2-3
W
OUTPUTS
TURBIDITY SENSE
DISPENSERS
HEATER
DRAIN MOTOR
FAN/DAMPER
PUMP MOTOR
WATER VALVE
WATER HEAT DELAY
WATER HEAT DELAY
27
45
0.4
75
60
90
90
447
60 1
1
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
1
1
0
0
0
1
1
1
0
X
1
1
0
0
0
1
0
0
0
1
1
1
1
1
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
1
1
1
0
0
0
0
0
1
1
2
3
4
FILL/DISPENSER
STEP
TOTAL TIME (SEC)
WAT E R VALVE
CIRCULATION MOTOR
DRAIN MOTOR
HEATER
DISPENSER
FAN UNIT
SENSING LED
WASHING LED
SANITIZED LED
DRYING LED
CLEAN LED
FILL
WASH/HEAT
PAUSE
WASH/HEAT
WASH/HEAT/DISP.
DRAIN
DRY
TOTAL
CLEAN LED stays on until door is opened or cycle is started.
X - denotes selectable option
5
6
7
8
0
0
0
0
0
0
1
0
(Some models)
0
0
0
0
0
0
ULTIMATE/MAXX
P2- 4
P2- 5
P2- 6
BK
W
R
HALL SENSOR
DISPLAY
Y/BL
P2-13
P2-12
BK-W
P2-11
R
P32-6
BK
P32-9
FAN DRY UNIT
R-W
RINSE LED
SENSING LED
0
0
0
1
1
0
0
0
1
RINSE LED
Device being monitored
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
Fan damper
Display flashes when
Detection of failure
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
Turbidity
Fan speedFan speed
Rinse aid
Thermistor
Uo
Tu
HS
UF
HS
Th
RA
Display Codes (Readout)
Y-BK.............Yellow/Black
R-W..................Red/White
R-Y..................Red/Yellow
VIO..........................Violet
BK-W............. Black/White
SPEED WASH
RINSE ONLY
*Note: The Sahara/Maxx Dry will extend drying time by approximately 20 min.
To Previous Page
Loading...
