WIRING DIAGRAM
If grounding wires, screws or clips used to complete a path to ground are removed
for service, they must be returned to their original position and properly fastened.
Certain internal parts are intentionally NOT grounded and may present a risk of
electric shock only during servicing. Do not contact the following
parts while the
appliance is energized: pump, drive motor and electronic control boards.
This information is intended for use by technicians possessing
adequate background of electrical, electronic and mechanical
experience. Any attempt to repair a major appliance may result in
personal injury and property damage. The manufacturer or seller
cannot
be responsible for the interpretation of this information, nor
can it assume any liability in connection with its use.
IMPORTANTIMPORTANT SAFETY NOTICE
TECH SHEET - RETAIN FOR SERVICE TECHNICIAN
Disconnect from Electrical Supply Before Servicing Washer.
PART NO. 134968300 A
Motor Will Not Run
Timer/off
Door/open
SWITCH
POSITION
CIRCUIT
WATER TEMP SWITCH
H/C
XX
X
W/C
X
X
X
C/C
X
W/W
NOT ON ALL MODELS
X= CONTACTS CLOSED
*
*
1 - 31 - 5
2 - 4W/R
C10.10 (D)
C10.9 (E)
C10.6 (C)
C10.1 (B)
C10.2 (A)
C10.5 (TM)
CYCLE
SIGNAL
DOOR
LOCK
COIL
DOOR
LAMP
TIMER
MOTOR
C6.5 (AC)
C6.6 (AC)
C6.2 (P2)
C6.3 (P3)
C6.1 (P1)
C6.4
C10.3 (T2)
C10.4 (T1)
T
B
RINSE
WATER
CYCLE
SIGNAL
TIMER
DIRECT
RINSE
WATER
WASH
WATER
WASH
WATER
BLK/WHT
2
1
WHT
WHT/RED
BLUE
RED/YEL
ORG
BROWN
RED/BLK
TAN/WHT
YEL/WHT
YELLOW
ORG/GRAY
YEL/BLK
AQUA
BLK/RED
TAN/BLK
ORG/WHT
TAN
BLUE
YEL
BLUE
PINK/BLK
WHT/RED
BROWN
YEL/BLK
B
2B
4
2
MOTOR CONTROL
B
T
10
2
5
3
14
8
T
12
B
T
0T 0C
BLEACH
SOFTENER
TEMP
SWITCH
HOT
PINK
COLD
L1
BLEACH
SOFTENER
MS
4.4
2.1
WATER
VALVES
DISPENSER
VALVES
WATER LEVEL
PRESSURE
SWITCH
2.2
4.3
DOOR
LOCK
SWITCH
LINE SWITCH
PUSH-PULL
7B5B3B1B
6T
7C5C3C1C
6C
1
2
3
M
SIGNAL
SWITCH
PUMP
MOTOR
T
GRAY
B
14
#2
#6
WAX
MOTOR
PTC
+t
2
1
ORG/BLK
GREEN
653
24
1
TACHO-
GENERATOR
T
MOTOR
WINDING
1. CHECK FOR POWER:
Advance the timer knob to the drain
increment. If the drain pump does not run,
check household safety circuit. If the drain
pump runs go to step 2.
2. CHECK FOR MOTOR MOVEMENT:
Turn the water off to the washer. Remove
electrical power from the washer and
remove the back
panel. Remove the motor
drive belt. Reconnect electrical power and
set the timer to the start of the Regular wash
cycle and pull the knob out. If motor does
not rotate, check for a poor connection in the
timer line switch or door lock switch. If good,
and motor does not run
go to step 3.
3. MEASURE VOLTAGES:
Remove the six pin plug from the speed
control unit. Measure the voltage between
pins 5 and 6 on the harness. If the meter
reads 0 check the connection in the timer
line switch or door lock. If the meter
reads 120 Vac go to step 4.
4. Set the timer to the Heavy Wash position of
the Regular wash cycle. Remove the ten pin
plug from the speed control unit. Measure
the voltage between pins 1, 2, 6 and 10 of
the ten pin plug to pin 5 of the 6 pin plug on
the harness. The voltage at pins
2, 6, and
10 should read 120 Vac and 0 Vac at pin 1.
If not, check timer contacts 1C to 1B, 5C to
5B, and 7C to 7B for closed contacts, and
3C to 3B for open contacts. If the voltage
readings are correct, go to step 5.
5. MEASURE RESISTANCES:
Check the
fuse on the speed control board.
If the fuse is open, replace the speed control
board. If good, go to step 6.
6. Remove the 6 pin plug from the speed
control unit. Measure the resistance
between pins 1 and 2, 2 and 3, and 3 and 1
of the speed control unit. If the
meter reads
other than 3 Meg ohms ± 10%, replace the
speed control board.
7. Remove electrical power from the washer.
With an ohmmeter check the resistance
between pins 1 and 2, 2 and 3, and 3 and 1
of the six pin plug on the harness. If the
meter reads other than 2.6 ohms
± 7%,
replace the motor.
Quick Facts
• The timer motor will not run continuously.
The speed control unit controls the timer
motor and advances the timer when needed.
•In some tumble modes, the tub may not
tumble for the first 16 to 20 seconds after
start-up.
• Extremely low water pressure may cause
tub rotation to stop until WLC satisfied.
GRN
WHT
WHT
WHT
WHT
#1
#7
N
GND
CABINET
CHASSIS
#3
Speed
Control
6
1
Speed
Control
6
1
Speed
Control
6
1
510
16
BLK
#4
YEL/RED
EXTRA
RINSE
SWITCH
T
NOTE: BOLD LINES INDICATE INTERNAL TIMER JUMPER WIRES.
DASHED LINES INDICATE CIRCUITS NOT ON ALL MODELS.
RED
4.2
4.1
TEST CONNECTOR
WAX MOTOR
SWITCH
1
2
WHT/RED
To Next Page
Need help?
General
