Fuji Electric FLD-1

To Next Page

To Previous Page

INF-TN1FSC-E 153

(5) Install the printer with 2 screws.

(6) Install the rubber guards

Note) Install it so that the groove of the rubber guards may ﬁ t tightly on the edges of the main

unit.

(7) Turn ON the power supply of the main unit.

Main Page

PREFACE2
CONTENTS3
WARNING SYMBOLs AND THEIR MEANINGS6
SAFETY PRECAUTIONS7
1. OVERVIEW10
2. CHECK OF DELIVERED ITEMS11
- 2.1 On purchase of flow transmitter (type: FSC)11
- 2.2 On purchase of detector (type: FLD)12
- 2.3 On purchase of flow velocity distribution measurement detector (type: FSD)13
3. CHECK MODEL AND SPECIFICATION14
4. NAME AND EXPLANATION OF EACH PART17
- 4.1 Name and explanation of main unit and detector17
- 4.2 Explanation of keys19
- 4.3 Handling of SD memory card20
5. POWER ON AND POWER OFF25
- 5.1 Operating power supply25
- 5.2 Turning on the power and language preference26
- 5.3 Power OFF27
6. WIRING28
- 6.1 Diagram28
- 6.2 Connection of dedicated cables28
- 6.3 Connection of analog input/output cable(4 to 20 mA DC)29
- 6.4 Connection of USB cable29
7. INPUT OF PIPING SPECIFICATIONS30
- 7.1 Display of pipe setup screen30
- 7.2 Entry of site name (not required measurement)33
- 7.3 Outer diameter of piping (unit: mm)(range: 13 to 6000 mm)36
- 7.4 Piping material37
- 7.5 Wall thickness (unit: mm) (range: 0.1 to 100.00mm)38
- 7.6 Lining material39
- 7.7 Lining thickness (unit: mm) (range: 0.01 to 100.00 mm)40
- 7.8 Kind of fluid41
- 7.9 Viscosity42
- 7.10 Selection of sensor mounting method43
- 7.11 Kind of sensor44
- 7.12 Transmission voltage (used when an indicator is 1 or less during measurement)45
- 7.13 Completion of PROCESS SETTING46
8. MOUNTING OF DETECTOR47
- 8.1 Selection of mounting location47
- 8.2 Selection of detector50
- 8.3 Use of surface-treated accessories52
- 8.4 How to mount small size (standard) sensor and small outer diameter sensor to pipe53
  - 8.4.1 How to mount a sensor (V method)53
  - 8.4.2 How to mount a small size (standard) sensor (Z method)54
- 8.5 How to mount large and medium size sensor56
- 8.6 How to mount high temperature sensor to pipe63
  - 8.6.1 How to mount a sensor (V method)63
  - 8.6.2 How to mount a sensor (Z method)64
- 8.7 How to fold gage paper (used for determining mounting position)66
9. START MEASURING67
10. Setting Operation (Application)72
- 10.1 How to use SITE SETUP function (SITE SETUP page)73
- 10.2 Setting of data logger function85
- 10.3 Setting of system (SYSTEM SETUP screen)97
- 10.4 Setting of range (setting screen for input/output range)115
  - 10.4.1 Setting the input range: When setting the range for the input current or input voltage.Setting range: 0.000 to ±9999999999115
  - 10.4.2 Setting the output range117
- 10.5 Use of printer function (PRINTER screen)121
- 10.6 Maintenance function (MAINTENANCE screen)126
- 10.7 Flow velocity distribution display function (optional)139
  - 10.7.1 Installing Detector139
  - 10.7.2 Operation144
- 10.8 Contents of errors in status display149
  - 10.8.1 How to check status display149
  - 10.8.2 Action on error150
11. MAINTENANCE AND CHECKUP153
12. ERROR AND REMEDY155
- 12.1 Error in LCD Display155
- 12.2 Error of key155
- 12.3 Error in measured value156
- 12.4 Error in analog output159
13. EXTERNAL COMMUNICATION SPECIFICATION160
14. HOW TO USE PRINTER161
- 14.1 How to connect printer161
- 14.2 How to load printer roll sheet163
15. REPLACEMENT OF BUILT-IN BATTERY164
16. APPENDIX165
- 16.1 Piping data165
- 16.2 Command tree173
- 16.3 Specifications175
- 16.4 Q & A180
- 16.5 File contents of SD memory card185

Fuji Electric FLD-1 - Page 162

Table of Contents

Related product manuals