Fuji Electric FRENIC-Ace series - Page 188

5.2 Function Codes Table
5-18
Code Name Data setting range
Change when running
Data copying
Factory
Default
Drive control
Related page
V/f
PG V/f
w/ PG
Torque control
PM
H47
Initial capacitance of DC link
bus capacitor
For adjustment at replacement
(0000 to FFFF in hexadecimal)
Y
N
–
Y
Y
Y
Y
Y
5-173
H48
Cumulative run time of
capacitors on printed circuit
boards
For adjustment at replacement
Change in cumulative motor run time (Reset is enabled)
(in units of ten hours)
Y
N
–
Y
Y
Y
Y
Y
5-169
5-173
H49
Starting mode
(Auto search delay time 1)
0.0 to 10.0 s
Y
Y
0.0
Y
Y
Y
N
Y
5-174
H50
Non-linear V/f 1 (Frequency)
0.0 (Cancel), 0.1 to 500.0 Hz
N
Y
0.0
Y
Y
N
N
N
5-174
H51
(Voltage)
0 to 240 V:AVR operation ( 200 V class)
0 to 500V:AVR operation ( 400V class)
N
Y2
0
Y
Y
N
N
N
H52
Non-linear V/f 2 (Frequency)
0.0 (Cancel), 0.1 to 500.0 Hz
N
Y
0.0
Y
Y
N
N
N
H53
(Voltage)
0 to 240V:AVR operation ( 200V class)
0 to 500V:AVR operation ( 400V class)
N
Y2
0
Y
Y
N
N
N
H54
Acceleration time (Jogging)
0.00 to 6000 s
Y
Y
6.00
or
20.0
*10
Y
Y
Y
N
Y
5-174
H55
Deceleration time (Jogging)
0.00 to 6000 s
Y
Y
Y
Y
Y
N
Y
H56
Deceleration time for forced
stop
0.00 to 6000 s
Y
Y
Y
Y
Y
N
Y
H57
1st S-curve acceleration range
(At starting)
0 to 100%
Y
Y
10
Y
Y
Y
N
Y
H58
2nd S-curve acceleration
range (At arrival)
0 to 100%
Y
Y
10
Y
Y
Y
N
Y
H59
1st S-curve deceleration
range (At starting)
0 to 100%
Y
Y
10
Y
Y
Y
N
Y
H60
2nd S-curve deceleration
range (At arrival)
0 to 100%
Y
Y
10
Y
Y
Y
N
Y
H61
UP/DOWN control
(Initial frequency setting)
0: Initial value is 0.00 Hz
1: Last UP/DOWN command value on releasing the run
command.
N
Y
1
Y
Y
Y
N
Y
5-174
H63
Low limiter (Mode selection)
0: Limit by F16 (Frequency limiter: Low) and continue to
run
1: If the output frequency lowers below the one limited by
F16 (Frequency limiter: Low), decelerate to stop the
motor.
Y
Y
0
Y
Y
Y
N
Y
5-174
H64
(Lower limiting frequency)
0.0: Depends on F16 (Frequency limiter, Low)
0.1 to 60.0 Hz
Y
Y
1.6
Y
Y
N
N
Y
5-174
H65
Non-linear V/f 3 (Frequency)
0.0 (Cancel), 0.1 to 500.0 Hz
N
Y
0.0
Y
Y
N
N
N
5-174
H66
(Voltage)
0 to 240V: AVR operation ( 200V class)
0 to 500V: AVR operation ( 400V class)
N
Y2
0
Y
Y
N
N
N
H68
Slip compensation 1
(Operating conditions
selection)
0: Enable during acceleration/deceleration, enable at
base frequency or higher
1: Disable during acceleration/deceleration, enable at
base frequency or higher
2: Enable during acceleration/deceleration, disable at
base frequency or higher
3: Disable during acceleration/deceleration, disable at
base frequency or higher
N
Y
0
Y
Y
N
N
N
5-174
H69
Anti-regenerative control
(Mode selection)
0: Disable
2: Torque limit control with force-to-stop
(Cancel limit control after three times of deceleration
time has passed)
3: DC link bus voltage control with force-to-stop
(Cancel voltage control after three times of deceleration
time has passed)
4: Torque limit control without force-to-stop
5: DC link bus voltage control without force-to-stop
Y
Y
0
Y
Y
Y
N
Y
5-175
H70
Overload prevention control
0.00: Follow the deceleration time selected
0.01 to 100.00 Hz/s, 999 (Cancel)
Y
Y
999
Y
Y
Y
N
Y
5-176
H71
Deceleration characteristics
0: Disable 1: Enable
Y
Y
0
Y
Y
Y
N
N
5-176
H72
Main power shutdown
detection
(Mode selection)
0: Disable 1: Enable
(Available FRN0088E2

-2

/FRN0059E2

-4

or above)
Y
Y
1
Y
Y
Y
Y
Y
5-176
H74
Torque limiter *5
(Control target)
0: Torque limit
1: Torque current limit
N
Y
1
N
N
Y
Y
Y
5-177
H76
Torque limiter (Braking)
(Frequency rising limiter
for
braking)
0.0 to 500.0Hz
Y
Y
5.0
Y
Y
N
N
N
5-177
H77
Service life of DC link bus
capacitor
0 to 8760 (in units of ten hours)
Y
N
6132
(ND spec)
Y
Y
Y
Y
Y
5-177
*5: Available at ROM version 0300 or later.
*10: 6.00s for inverters of nominal applied motor 22kW or below; 20.0s for those of 30kW or above.